RunRyder RC
 9  Topic Subscribe
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 3315 views POST REPLY
Scorpion Power Scorpion Power
HelicopterFlybarless Rotor Head SystemsBeastX › Beastx setup question
01-01-2011 05:08 PM  6 years agoPost 21
nickwap

rrVeteran

Berwick-upon-Tweed, Northumberland, England

My Posts: All  Forum  Topic

+1 ^

With regards to piro optimization, you will tell easily if you get it wrong.
My 700N pitched nose up during FFF Piros with the wrong setting, no drama, but obvious!

Nick

"Give me another one, this one's broke!"

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-01-2011 10:50 PM  6 years agoPost 22
Jej34

rrApprentice

N.J

My Posts: All  Forum  Topic

I set my beastx for "extreme" and flew it.
It was better but I'm nit getting a super wick roll that I'm looking for. I must be doing something wrong?

PM  EMAIL  GALLERY  Attn:RR
01-02-2011 03:37 AM  6 years agoPost 23
maj

rrVeteran

united Kingdom

My Posts: All  Forum  Topic

Just increase your dual rate for the axis you want to speed up. It should be that simple.

MJ

PM  EMAIL  Attn:RR
01-02-2011 04:49 AM  6 years agoPost 24
az_heliguy

rrKey Veteran

San Tan Valley, AZ

My Posts: All  Forum  Topic

all mine are set to pro and its wicked fast. what heli did you have it installed on again?

Mastercard Team Pilot :)

PM  EMAIL  GALLERY  Attn:RR
01-02-2011 03:56 PM  6 years agoPost 25
merlin3

rrKey Veteran

dayton, ohio

My Posts: All  Forum  Topic

just set it to radio and use your atvs

Justin - Team Horizon, Team Byron
2-700x, Trex 700n, small helis

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-08-2011 07:11 PM  6 years agoPost 26
Chapter

rrApprentice

Savannah, usa

My Posts: All  Forum  Topic

In the number-2 video he said, the very first point (A) in Setup Menu is setting up for Flybarless (blue light) or normal flybar (red light) but according to the menu point (A) refers to Mounting orientation of the Microbeast, point (B) is Swashplate servo frequency and so on....

His video number-2 point (B) is Setting up the Mounting Orientation of the sensor but according to the menu is point (A) for setting up the Mounting Orientation. I'm comfuse!

I have the Version 2 instruction manual bought last December/10.

Can someone here explain please...

Thanks,

Chapter

PM  EMAIL  GALLERY  Attn:RR
01-08-2011 07:33 PM  6 years agoPost 27
the collective

rrKey Veteran

Bayside, NY, U.S.A

My Posts: All  Forum  Topic

Chapter,

Those videos were shot using version 1 firmware. Always follow the manual for the version you are actually running.

PM  EMAIL  Attn:RR
01-08-2011 07:44 PM  6 years agoPost 28
Chapter

rrApprentice

Savannah, usa

My Posts: All  Forum  Topic

OK great! thank you Collective.

The menu version 2 also mention about Receiver Type Setup.

I guess this has to be done before get into the Setup Menu and Parameter Menu right?

There are 5 different types of receiver you can select according to version 2.
1) Standard receiver
2)Spektrum Satelite
3)Futaba S-BUS
4)SRXL
5)PPM

For my setup, I will use option-1 (Standard receiver) just like in his number-1 video.

Chapter

PM  EMAIL  GALLERY  Attn:RR
01-08-2011 08:36 PM  6 years agoPost 29
Quebec X50

rrNovice

Quebec, Canada

My Posts: All  Forum  Topic

Thank you for de link.

JR NEX6, JR VIBE E8, JR VIBE NEX 50

PM  EMAIL  GALLERY  Attn:RR
01-27-2011 02:19 PM  6 years agoPost 30
Sidneyw

rrApprentice

Huntersville, NC

My Posts: All  Forum  Topic

OK great! thank you Collective.

The menu version 2 also mention about Receiver Type Setup.

I guess this has to be done before get into the Setup Menu and Parameter Menu right?

There are 5 different types of receiver you can select according to version 2.
1) Standard receiver
2)Spektrum Satelite
3)Futaba S-BUS
4)SRXL
5)PPM

For my setup, I will use option-1 (Standard receiver) just like in his number-1 video.

Chapter
Got me fooled for a few minutes with receive types as the language was not very clear. If receiver is used (any type or brand) use option 1.

There is no video instruction for version 2 and up. All videos at youtube were done with version 1 firmware which is markedly different than V2.

PM  EMAIL  GALLERY  Attn:RR
03-23-2011 09:58 PM  6 years agoPost 31
Quebec X50

rrNovice

Quebec, Canada

My Posts: All  Forum  Topic

Small tail wawe!

I this is my setup and my Probleme is small tail wawe

Thundertiger X50
Compass FblHead
OS 55 Hyper
JR8917HV cyclic
JR8900G tail
Beast X 3Axis Gyro
lipo 7.4v 1800m
Spektrum 7100R
Governor

Aile D/R 85 EXP 10
Elev D/R 85 EXP 10
RUD D/R 100 EXP 20

Gyro Gain Norm 65%
Idle 1 60%
Idle 2 60%
Pot on the BeastX 1 0% original position
2 0%
3 0%

If i put less than 65% my tail wawe all the time,
Some people a answer for me???

Thank

JR NEX6, JR VIBE E8, JR VIBE NEX 50

PM  EMAIL  GALLERY  Attn:RR
03-23-2011 10:06 PM  6 years agoPost 32
az_heliguy

rrKey Veteran

San Tan Valley, AZ

My Posts: All  Forum  Topic

Try and raise the gain a little bit. The pot for tail dynamics is for tail stopping. I set that pot a little higher then at stock settings. Fairly aggressive that way.

Mastercard Team Pilot :)

PM  EMAIL  GALLERY  Attn:RR
03-24-2011 12:04 AM  6 years agoPost 33
Quebec X50

rrNovice

Quebec, Canada

My Posts: All  Forum  Topic

Thank you, I try this setting tomorow.

JR NEX6, JR VIBE E8, JR VIBE NEX 50

PM  EMAIL  GALLERY  Attn:RR
03-24-2011 12:16 AM  6 years agoPost 34
az_heliguy

rrKey Veteran

San Tan Valley, AZ

My Posts: All  Forum  Topic

And if that doesn't work, move the ball on the rudder servo closer to the center by o.e position.

Mastercard Team Pilot :)

PM  EMAIL  GALLERY  Attn:RR
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 3315 views POST REPLY
Scorpion Power Scorpion Power
HelicopterFlybarless Rotor Head SystemsBeastX › Beastx setup question
 Print TOPIC  Make Suggestion 

 9  Topic Subscribe

Thursday, September 21 - 10:30 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online