RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 927 views
HelicopterFlybarless Rotor Head SystemsSkookum › Need Help Skookum 720
06-05-2010 09:34 PM  7 years agoPost 1
helipulse

rrApprentice

Toronto, ON, CANADA

My Posts: All  Forum  Topic

I fly 90 size Blitz Avro and I need some help.

I am using Reactor X now as My servos are for 6V and so how do I connected the reactor X to the skookum Bus?

Radio I am using is JR x9303

How do I connect ATG governor to the skookum

How do I connect Switch Glo to the skookum unit.

Any help will be appreciated.

Bhushan

PM  EMAIL  GALLERY  Attn:RR  Quote
06-06-2010 11:37 PM  7 years agoPost 2
helipulse

rrApprentice

Toronto, ON, CANADA

My Posts: All  Forum  Topic

Never mind, got everything working now. Will try flying next weekend now.

PM  EMAIL  GALLERY  Attn:RR  Quote
06-07-2010 02:22 AM  7 years agoPost 3
Gernejr

rrKey Veteran

Miami, Fl

My Posts: All  Forum  Topic

Well don't hold back , "Tell us how you do it" ... Really not alot of info on SK720. How you setup Gov and Switchglo?

Sponsored by Visa

PM  EMAIL  GALLERY  Attn:RR  Quote
06-07-2010 04:00 AM  7 years agoPost 4
helipulse

rrApprentice

Toronto, ON, CANADA

My Posts: All  Forum  Topic

This is set up:

I am using reactor X to drop the voltage down--- so.

servo wires input to reactor X.
Servo output to the Skookum bus (channel CENTER, LEFT AND RIGHT). These 3 wires are delivering the power-so I am not using battery directly plugged to the BUS.

Jumper installed as shown on manual (this step is imp)

In X9303 radio (under device select-)go to gear channel and select Governor mode.

In skookum software go and select 9 channels 1 gain and 3 Aux.

So when u select this, gain will be controlled by only Aux 2 switch.

Now install the (i am using atg) blue wire to: IO-B port on the bus. --gear channel controlled--so now u can change headspeed in x9303 radio.

The other atg wire goes to the T(throttle) on the bus.

in X9303 under "device select" go to AUX 4-click on it and select-aux 3-which means that aux 3 lever on right will now control it.

Switch glo wire gets plugged in IO-D and now u can turn it on and off by using the lever on the right.

make sure the 4 cables from the bus to the skookum are attached as shown in the manual.

If you have more questions, please feel free to pm me. I wish manual was more clear.

You are done.

PM  EMAIL  GALLERY  Attn:RR  Quote
06-08-2010 03:42 AM  7 years agoPost 5
Gernejr

rrKey Veteran

Miami, Fl

My Posts: All  Forum  Topic

Thanks , Now if i could just the 720 to show up at the door..

Sponsored by Visa

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 927 views
HelicopterFlybarless Rotor Head SystemsSkookum › Need Help Skookum 720
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Thursday, December 14 - 12:25 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online