RunRyder RC
 4  Topic Subscribe
WATCH
 1 page 1062 views POST REPLY
Scorpion Power Scorpion Power
Helicopter
e-
Henseleit TDR MP-XLE MP-E
› Ready for my TDR
06-04-2010 07:14 PM  7 years agoPost 1
UH-60PILOT

rrVeteran

Seoul, South Korea

My Posts: All  Forum  Topic

I got the word from Jan last week! Yesterday I wired Jan the money and ordered everything I need to make my TDR experience as good as possible. Here's what I'm getting

Helicopter: Henseleit TDR with yellow canopy, dark gray windshield decal and the blue comet tail decal.

Blades: Radix 710 mains and 105 tails

Motor: Pyro 700-52

ESC: Jive 120 HV

Swash servos: Futaba BLS 451

Tail servo: Futaba BLS 251

Flybarless unit: V-Bar 4.0

Transmitter: DX7 SE

Batteries: Hyperion 5000mah 6S2P 35C

Charger: Hyperion duo with 40 amp power supply.

Is there anything I'm missing?

Kenny Thompson

PM  EMAIL  GALLERY  Attn:RR  Quote
06-04-2010 08:33 PM  7 years agoPost 2
matjev

rrNovice

montfort netherlands

My Posts: All  Forum  Topic

tdr

Hi would use a small 4cell bufferbattery the jive bec can shut down completly
It happend to mine tdr i had a lot of luck that it was still standing on the ground The jive has a perfect governer but if something is broken inside you can throw it in the garbage Mine jive 120 is broken i send it last monday to kontronik until now kontronik service was not very nice to my

PM  EMAIL  Attn:RR  Quote
06-04-2010 09:43 PM  7 years agoPost 3
UH-60PILOT

rrVeteran

Seoul, South Korea

My Posts: All  Forum  Topic

Matjev, Thanks for the info.

Kenny Thompson

PM  EMAIL  GALLERY  Attn:RR  Quote
06-07-2010 09:08 AM  7 years agoPost 4
OICU812

rrMaster

Edson, Alberta, Canada

My Posts: All  Forum  Topic

Get this..

http://www.readyheli.com/9250-Kontr...ng_p_32120.html

Take off ferrite ring, use this as your slave wire, male to male in slave port of BEC output. Or make your own, its just a 12-14" male to male servo wire..

BTW...

I run 6 Jives, all use internal BEC no issues. With the Futaba servos you list 100% safe to run 6Volts. I am running internal on my Rigid at 6Volts, main and slave to be sure, no biggie.

Take time to read manual well, it is abit of story but done well. Especially take time on your main, secondary gear spacing and shimming and be prepared to hate putting on the canopy decals.

...Once upon a time there were Nitros, flybars and frequency pins...

PM  EMAIL  GALLERY  Attn:RR  Quote
06-07-2010 04:49 PM  7 years agoPost 5
UH-60PILOT

rrVeteran

Seoul, South Korea

My Posts: All  Forum  Topic

OICU812, Thanks for the tips. That connector is pricey but I think I can manage soldering three wires together and make one custom length right here at the house.

Kenny Thompson

PM  EMAIL  GALLERY  Attn:RR  Quote
06-12-2010 02:07 PM  7 years agoPost 6
EPGuy

rrNovice

UK

My Posts: All  Forum  Topic

Hi Guys

I was told early june for my Rigid delivery but still have not been asked for payment anyone in the same situation as me.

Does Jan ask for payment long before shipping?

I want one now

Edd

PM  EMAIL  Attn:RR  Quote
06-12-2010 04:45 PM  7 years agoPost 7
UH-60PILOT

rrVeteran

Seoul, South Korea

My Posts: All  Forum  Topic

Jan runs a pretty tight schedule. You will get an email from him about a week before your machine is ready to ship. In the email he will prompt you for the options you want with your kit. I found his price on the Radix main and tail blades were cheaper than the places I found online so I ordered them from him. He will include all of his banking information so you can have the money wired into his account. That's what I did last week and I should be receiving my kit in the next two to three weeks. So, that's how it works. If you want to check on when your kit will be ready then go to henseleit helicopters online and then click on information on the upper left side of the screen. You will see the latest adjusted shipping schedule for the time periode you placed your order. Hope this helps.

Kenny Thompson

PM  EMAIL  GALLERY  Attn:RR  Quote
06-12-2010 05:35 PM  7 years agoPost 8
EPGuy

rrNovice

UK

My Posts: All  Forum  Topic

Thanks for the info.

looks like early July now when i get my kit

Edd

PM  EMAIL  Attn:RR  Quote
06-13-2010 07:05 PM  7 years agoPost 9
mrhelichopper

rrApprentice

The Netherlands

My Posts: All  Forum  Topic

Same experience for me. The email asking for payment is very close to the time of shipping.

I love mine and hope you enjoy yours as much as I am enjoying mine :-)

http://www.youtube.com/profile_videos?user=mrhelichopper mrhelichopper@googlemail.com

PM  EMAIL  GALLERY  Attn:RR  Quote
06-13-2010 09:37 PM  7 years agoPost 10
OICU812

rrMaster

Edson, Alberta, Canada

My Posts: All  Forum  Topic

You guys need some pics of yours in galleries!! Seems many have them up now and flying them, time to start an official thread me thinks.

...Once upon a time there were Nitros, flybars and frequency pins...

PM  EMAIL  GALLERY  Attn:RR  Quote
06-13-2010 09:41 PM  7 years agoPost 11
mrhelichopper

rrApprentice

The Netherlands

My Posts: All  Forum  Topic

I put my favorite one in there :-)

http://www.youtube.com/profile_videos?user=mrhelichopper mrhelichopper@googlemail.com

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1062 views POST REPLY
Scorpion Power Scorpion Power
Helicopter
e-
Henseleit TDR MP-XLE MP-E
› Ready for my TDR
 Print TOPIC  Make Suggestion 

 4  Topic Subscribe

Monday, October 23 - 12:29 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online