RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 416 views POST REPLY
Scorpion Power Scorpion Power
Helicopter
e-
Align
T-REX 600 › Speed ctrl issue....
12-31-2009 09:47 PM  7 years agoPost 1
avigilad99

rrApprentice

israel

My Posts: All  Forum  Topic

Hi guys...

Just got my 600ESP,now I have conected the battery to the speed controller wich I'v connected to the motor and the reciver and nothing
hapens....

What's wrong?

Avi Gilad

PM  EMAIL  GALLERY  Attn:RR  Quote
12-31-2009 10:35 PM  7 years agoPost 2
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

Futaba radio? Reverse your throttle channel. Set a linear 0 to 100% throttle curve before you try to program it.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
12-31-2009 10:40 PM  7 years agoPost 3
avigilad99

rrApprentice

israel

My Posts: All  Forum  Topic

JR 2.4

I'm not talking about getting the engine work, I'm talking about getting the Radio into work

Avi Gilad

PM  EMAIL  GALLERY  Attn:RR  Quote
01-01-2010 12:25 AM  7 years agoPost 4
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

I have conected the battery to the speed controller wich I'v connected to the motor and the reciver and nothing
hapens....
That sounds as if you have everything installed, but the ESC won't arm and turn the motor. That is usually an indication that the throttle channel is reversed (a common happening if you use a Futaba radio).
I'm talking about getting the Radio into work
That sounds as if nothing moves -- servos OR motor.

JR 2.4 what? X9303? 12X? Older JR radio with the Spektrum module?

This could be something as basic as having to bind your receiver to your transmitter.

To do THAT, you insert the binding plug into the BATTERY port of your receiver. Plug an RX battery pack into ANY available socket of your receiver. The yellow leds on the RX will begin to flash. Your transmitter has a button on the back -- press it in WHILE you turn on the TX. Hold the button in until the yellow LED(s) on the RX go solid. When that happens, turn off the RX, unplug the binding plug, then turn off the TX.

Now, the next time you turn on your TX and RX, the yellow leds should go on solid and you'll have a functioning radio.

-----

What JR radio do you have, and what receiver are you working with?

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
01-01-2010 06:37 AM  7 years agoPost 5
avigilad99

rrApprentice

israel

My Posts: All  Forum  Topic

I know, I'v treid to bind theme, not working...

The radio is DX-7 with JR reciver,I think the RX may B damaged, or some electronic stuff is missing.

Does everything should be connected at the next order?:

Motor
|
|
Speed controll--->Battery
|
|
Rx

Avi Gilad

PM  EMAIL  GALLERY  Attn:RR  Quote
01-01-2010 06:53 AM  7 years agoPost 6
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

Find or borrow a standard 4-cell Nicad or NiMh receiver battery.

The BIND plug has to be plugged into the battery port of your receiver. No other slot will work for binding.

When you plug the bind plug into the battery port, then plug your battery into any available slot in the RX. Make sure you have the battery polarity correct.

At this point, the LEDs in the RX should be flashing. ARE THEY?

Push the button on the back of the transmitter, hold it in, and turn on the TX. Keep holding that button IN until the LEDs stop blinking and go on solid.

Turn everything off. Remove the bind plug.

I will assume that since this is a DX7, you're trying to bind an AR7000 receiver to it. Are you using an AR7000, or a different receiver? Make sure the auxiliary receiver is plugged into the main RX and that the plugs are fully seated in the cable that connects the two.

When you bind, move the transmitter a couple of feet away from the RX.

-----

As for your connections...

The three motor wires from the ESC connect to the motor. If it spins backwards, then reverse any two of those three wires.

The battery plugs into the two wires coming from the ESC -- Red and Black. Red is +, black is -.

The three wire cable with the RX connector plugs into the receiver's THROTTLE slot. Make sure you get the plug installed right, and not upside down.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 416 views POST REPLY
Scorpion Power Scorpion Power
Helicopter
e-
Align
T-REX 600 › Speed ctrl issue....
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, October 24 - 5:11 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online