RunRyder RC
 5  Topic Subscribe
WATCH
 1 page 1201 views POST REPLY
Scorpion Power Scorpion Power
HelicopterJS Model TZ Shark, 3d Frenzy › Mounting Gov. sensor?
12-29-2009 09:13 AM  7 years agoPost 1
roccoym

rrNovice

McAllen Tx.

My Posts: All  Forum  Topic

Where is everyone mounting their governor sensors on their Frenzy's I have the newer version which has a small dimple on the start shaft for magnet installation, but I really cant find an area to get the sensor mounted.

If anyone has pics of their sensor installation on their Frenzy's please post. Thanks!

PM  EMAIL  GALLERY  Attn:RR  Quote
12-29-2009 11:46 AM  7 years agoPost 2
Andriyka

rrNovice

Kyiv, Ukraine

My Posts: All  Forum  Topic

Sensor setup on my Frenzy

www.tzfrenzy.info

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-29-2009 08:49 PM  7 years agoPost 3
roccoym

rrNovice

McAllen Tx.

My Posts: All  Forum  Topic

Thanks Andriyka

PM  EMAIL  GALLERY  Attn:RR  Quote
04-12-2010 10:05 PM  7 years agoPost 4
99grandtouring

rrNovice

Cross Lanes, WV

My Posts: All  Forum  Topic

is that an aftermarket or custom bracket?
I'm trying to figure out how to mount my align g600 gov sensor to my frenzy and ys50
Thanks!

PM  EMAIL  Attn:RR  Quote
04-12-2010 11:10 PM  7 years agoPost 5
resa man

rrNovice

uk

My Posts: All  Forum  Topic

Not sure if the 50 has it but I mounted my sensor magnets on the clutch bell and the sensor on the side frame

PM  EMAIL  GALLERY  Attn:RR  Quote
04-15-2010 11:57 AM  7 years agoPost 6
heli-cuzz

rrElite Veteran

Pittston, Pa. USA

My Posts: All  Forum  Topic

Use a backplate sensor if allowed.

Fury 55 NIB Furion6 CGY750 fbl helicopter-Frenzy CGY750 fbl nitro-Frenzy fbl NOBAR90

PM  EMAIL  GALLERY  Attn:RR  Quote
04-15-2010 07:19 PM  7 years agoPost 7
honda411

rrKey Veteran

Surprise, AZ USA

My Posts: All  Forum  Topic

i just ordered my frenzy last night, and i am going to put on the Futaba GV1 gov on it. but my question relating to this topic is; do have to counter balance the magnet you put on the cooling fan? because there is a magnet on one side, and not the other, or it will be out of balance, or would you cut holes in the oposite side of the magnet to balance it?

PM  EMAIL  GALLERY  Attn:RR  Quote
04-15-2010 07:34 PM  7 years agoPost 8
kc8qpu

rrElite Veteran

sc

My Posts: All  Forum  Topic

The easiest way is just to put the second magnet on. But if your going to drill holes you drill them on the same side as the magnet not opposite.

Carpe Diem!!!

PM  EMAIL  GALLERY  Attn:RR  Quote
04-16-2010 03:22 AM  7 years agoPost 9
99grandtouring

rrNovice

Cross Lanes, WV

My Posts: All  Forum  Topic

I went ahead and glued my magnets in my fan, I'm gonna run without the gov to start with to break in the engine.
To mount the sensor I'm gonna do kinda as above and just get a piece of flat steel or aluminum stock and make an extension for the sensor so it can sit below the fan.

PM  EMAIL  Attn:RR  Quote
04-16-2010 04:39 AM  7 years agoPost 10
x-planker

rrApprentice

Ontario, Canada

My Posts: All  Forum  Topic

I heard that some plp are using the futaba GV-1 brackets with the align gov...

PM  EMAIL  Attn:RR  Quote
04-22-2010 04:04 PM  7 years agoPost 11
flustercluck

rrVeteran

Newnan Ga (Just S. of ATL)

My Posts: All  Forum  Topic

Guys I'm sure you're running gov's on your Frenzy's... as a new Frenzy 50 owner I was wondering if there ever an answer as to whether there is an after-mkt bolt-on sensor bracket I could use w/ my ATG gov

I p/u a pr of rare-earth magnets from radio shack and jb'd them (after some dremel work) into the places as indicated on the underside of the fan

thx

Jeff

PM  EMAIL  GALLERY  Attn:RR  Quote
07-20-2010 08:47 PM  7 years agoPost 12
135boom

rrApprentice

Deerfield, Illinois

My Posts: All  Forum  Topic

I used the ATV GOV bracket for the 50 with slight elongation of the slots, no need for anything else. It really did not need much modification. I also mounted the magnet with 5min epoxy in the fan hub magnet location. Perfect add on for the TZ-50. My 90 will get one soon.

PM  EMAIL  Attn:RR  Quote
07-22-2010 05:00 AM  7 years agoPost 13
corvettercr

rrApprentice

erick oklahoma usa

My Posts: All  Forum  Topic

im using the multi gov. there was 3 or 4 mounting brackets with the kit. some long, some short, some shaped deff. i just picked one that fit. the others will work but i would have to gut onm them some. if ya need one i can send ya 1 that would come closest to fitting w/o major mods. ya might have to cut some on the length is all. run 2 magnets. one pos and the other neg. for bal. my sensor is like the pic in the top of the post. works great.

synergy n9, trex 250,450,600,700

PM  EMAIL  GALLERY  Attn:RR  Quote
07-22-2010 03:48 PM  7 years agoPost 14
flustercluck

rrVeteran

Newnan Ga (Just S. of ATL)

My Posts: All  Forum  Topic

Thx guys. Sold the Frenzy but appreciate the FB/offers.

cheers
Jeff

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1201 views POST REPLY
Scorpion Power Scorpion Power
HelicopterJS Model TZ Shark, 3d Frenzy › Mounting Gov. sensor?
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Saturday, October 21 - 12:30 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online