RunRyder RC
 10  Topic Subscribe
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 1932 views
Scorpion Power Scorpion Power
Helicopter
e-
Mikado
Other › It Begins!!!!
11-16-2009 07:08 PM  8 years agoPost 21
Riq

rrKey Veteran

ND

My Posts: All  Forum  Topic

I use 4200s.

PM  EMAIL  GALLERY  Attn:RR  Quote
11-16-2009 08:27 PM  8 years agoPost 22
OICU812

rrMaster

Edson, Alberta,​Canada

My Posts: All  Forum  Topic

Did u run a slave port wire from jive bec? Observe polarity markings on case that parralels output power. Should be able to almost stall servos with no brownout and u should also select 6volts output to as well for buffer voltage

...Once upon a time there were Nitros, flybars and frequency pins...

PM  EMAIL  GALLERY  Attn:RR  Quote
11-16-2009 08:32 PM  8 years agoPost 23
MTBSuspEng

rrNovice

Madison, Wi

My Posts: All  Forum  Topic

Currently running both the slave and master to the RX, I'm going to try running the slave directly to the Vbar. I'll recheck all my wiring this evening. Also I hear my problem could be due to the close proximity of the TX and RX indoors, so I'll take it outside this evening and see if anything changes. If problems continue I'll pick up a Spektrum flight log from the LHS.

PM  EMAIL  GALLERY  Attn:RR  Quote
11-16-2009 09:21 PM  8 years agoPost 24
OICU812

rrMaster

Edson, Alberta,​Canada

My Posts: All  Forum  Topic

Ya u should def have tx and RC a few feet apart and check slave wire polarity on bec output it's easy to get wrong aak me how I know lol

...Once upon a time there were Nitros, flybars and frequency pins...

PM  EMAIL  GALLERY  Attn:RR  Quote
11-16-2009 09:47 PM  8 years agoPost 25
Big Fil

rrKey Veteran

Santa Rosa, CA

My Posts: All  Forum  Topic

How heavy did it end up, any idea ?
The 10s hyperion g3vx 4200 are 1140g and the 3300 are 930g. Out of these two, which one would u guys use on a similar logo ?
My setup is almost exactly what MTBSuspEng's is and mine comes in at 7.98lbs AUW. Only difference is MTB is using far more velcro straps.

You'll want to run the 4200s for a Logo 600. I'm running the G3Vx packs and they CG well.

PM  EMAIL  GALLERY  Attn:RR  Quote
11-17-2009 04:46 AM  8 years agoPost 26
HeliMan Dave

rrVeteran

Suburban Chicago

My Posts: All  Forum  Topic

MTB, Looks good but a few things I'd like to point out.

#1, Be careful if you really leave the tail servo wire tucked inside the frame where the boom gets clamped. I would be nervous that the servo leads would get pinched when you sandwich the frames together and tighten the screws.

#2, I'd put the ground wire screw in the bottom of the boom instead of the side. On the inside of the boom, the belt will run very close to the screw and could get shredded.

#3 I'd find a different place to mount the satellite RX instead of directly on the side of the cyclic servo. Servos are very RF noisy and may cause unintended interference. I'd suggest the side of the main frame.

Logo 700 / 600 / 500 V-Bar NEO / Blade 180CFX / mCPX BL / Nano / V-Control

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 1932 views
Scorpion Power Scorpion Power
Helicopter
e-
Mikado
Other › It Begins!!!!
 Print TOPIC  Make Suggestion 

 10  Topic Subscribe

Thursday, November 23 - 4:58 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online