RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 1395 views
Helicopter
e-
Thunder Tiger
Other › innovator exp
09-03-2009 06:01 PM  8 years agoPost 1
team model

rrNovice

france

My Posts: All  Forum  Topic

Owning an innovator exp with 3d program, we get an engine failure while in negative flight, (engine) trim down. When I put the trim upside, there‘s no more failure but the negative pitch is deceased, which impairs flight on the back. Is here a solution?

Thanks

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-14-2009 10:46 PM  8 years agoPost 2
helibuyer lesodell3

rrNovice

springport mi usa

My Posts: All  Forum  Topic

when you do a setup make sure the trim for the power is in the middle

PM  EMAIL  Attn:RR  Quote
09-14-2009 11:48 PM  8 years agoPost 3
cwright

rrKey Veteran

Blossvale New York

My Posts: All  Forum  Topic

We had the same thing happen to the one we have at the shop where I work. You need to put the throttle trim 3 to 4 clicks above half way. Be careful when doing this because the headspeed becomes pretty high. We got this info from Ace directly. Also if you have the software disk double check the pitch and throttle curves in idle up. Ours was the same in both normal and idle up. We adjusted the curves before we tried it and got the dead motor while inverted. Putting the trim above half way did fix the problem though. Good luck. Chuck

PM  EMAIL  GALLERY  Attn:RR  Quote
09-15-2009 01:49 AM  8 years agoPost 4
helibuyer lesodell3

rrNovice

springport mi usa

My Posts: All  Forum  Topic

you should put the trim all the way up or you wont get all the pitch and yes you need to go into the software and add some pitch and head speed and take out some exp there is way to much . the guys at ace arnt so good with this heli they were telling people you couldnt run the carbon blades on the md530 and a lot of other things that were not right, over on rc groups there is a very good topic about the innv and you can here from people who have talked to ace , but ace is good at putting new parts on and getting them flying . i have 2 exp and love them one is setup to 3d and the other is a ez flyer

PM  EMAIL  Attn:RR  Quote
09-18-2009 01:28 PM  8 years agoPost 5
helibuyer lesodell3

rrNovice

springport mi usa

My Posts: All  Forum  Topic

well how is it going ?

PM  EMAIL  Attn:RR  Quote
09-18-2009 05:56 PM  8 years agoPost 6
team model

rrNovice

france

My Posts: All  Forum  Topic

Thank you has all j have retiree engine Governor mode
idulp and it works

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-18-2009 09:23 PM  8 years agoPost 7
helibuyer lesodell3

rrNovice

springport mi usa

My Posts: All  Forum  Topic

wow that is a lot of innovators , and good to here you got it going

PM  EMAIL  Attn:RR  Quote
09-21-2009 10:34 PM  8 years agoPost 8
pete05

rrApprentice

australia, western sydney

My Posts: All  Forum  Topic

got any close up photos of these helis?

PM  EMAIL  GALLERY  Attn:RR  Quote
09-22-2009 01:31 AM  8 years agoPost 9
helibuyer lesodell3

rrNovice

springport mi usa

My Posts: All  Forum  Topic

i really love this heli it has help me with my 3d flying its like a real life flight sim . if they would fix the junk landing gear and the tail blades are way to soft but it is a very ez heli to setup after you learn to move that %&#$ trim ALL the way up or your heli will fall out of the sky , its a great starter and a heli you can move up to flying 3d without putting a ton of money in it to do that and if you get the exp you dont have to put any money in it to get it to fly right or 3d or hover like a blade cx ,i have gotten 2 guys into helis with a innovator

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 1395 views
Helicopter
e-
Thunder Tiger
Other › innovator exp
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Thursday, December 14 - 8:20 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online