RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 663 views
HelicopterFlybarless Rotor Head SystemsOther › Synergy with 3dx head or rjx head
09-03-2009 03:13 PM  8 years agoPost 1
kjetil Tønnesen

rrNovice

Norge

My Posts: All  Forum  Topic

do i have to cut down the main shaft on my synergy to make it work well??when i am using the 3dx head or rjx head??

PM  EMAIL  GALLERY  Attn:RR  Quote
09-03-2009 03:19 PM  8 years agoPost 2
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Do you mean cut that shaft to make it shorter?

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-03-2009 03:48 PM  8 years agoPost 3
kjetil Tønnesen

rrNovice

Norge

My Posts: All  Forum  Topic

yes

PM  EMAIL  GALLERY  Attn:RR  Quote
09-03-2009 03:50 PM  8 years agoPost 4
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Not necessary If you want a lower head you can cut the shaft or get the Kasama Cyber head as it has different mounting holes for height......Ron

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-03-2009 03:54 PM  8 years agoPost 5
tr0cks

rrApprentice

NJ, 08344

My Posts: All  Forum  Topic

who has the 12mm cyber head available?

I remember when sex was safe and Heli's where dangerous.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-03-2009 04:12 PM  8 years agoPost 6
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

I did not realize the Synergy had a 12mm mainshaft. Cut away ......Ron

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-03-2009 04:21 PM  8 years agoPost 7
tr0cks

rrApprentice

NJ, 08344

My Posts: All  Forum  Topic

i'm using a rjx head now, but been thinking of doing the 3dx, due to horror stories i hear about the rjx swash driver breaking in flight.

I remember when sex was safe and Heli's where dangerous.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-03-2009 06:57 PM  8 years agoPost 8
kjetil Tønnesen

rrNovice

Norge

My Posts: All  Forum  Topic

ok i will go for the rjx head and sk 360 on my synergy!!i have had this setup before on a synergy,but then i cut the main shaft 2cm,a lot off work to drill the hole i the mainshaft for the rjx head,so i think i go for the stock length of main shaft

PM  EMAIL  GALLERY  Attn:RR  Quote
09-04-2009 05:36 PM  8 years agoPost 9
bullseye1

rrApprentice

Orange County, ca

My Posts: All  Forum  Topic

i'm using a rjx head now, but been thinking of doing the 3dx, due to horror stories i hear about the rjx swash driver breaking in flight
whatever you do make sure you get rid of the rjx swash driver, just drill and tap your stock washout hub with 3mm set screws(I use two, one on each side of the hub) and you never have to worry about it.

I found that out the hard way, a re kit on the 700 and a pipe after the cheap rjx swash driver broke in half in flight.

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 663 views
HelicopterFlybarless Rotor Head SystemsOther › Synergy with 3dx head or rjx head
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, December 12 - 4:19 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online