RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 346 views
HelicopterRadio - Servo - Gyro - Gov - Batt › help with revlock 10***PLZ***
09-01-2009 07:11 PM  8 years agoPost 1
jesus1895

rrApprentice

Tucson AZ

My Posts: All  Forum  Topic

i have gv-1's and when your setting up the sensor and magnets,you power the gv-1 up and you get the 97% reading on th escreen....how do you do that setup with the revlock?......destruction are not very clear to me..Maybe im just revlock dumb????

help.thx

AMA #224344

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-01-2009 09:38 PM  8 years agoPost 2
jsenicka

rrProfessor

Eagle River, WI

My Posts: All  Forum  Topic

Just get the sensor close to the magnet.
Power up the receiver. The RL sensor light should flash. Crank the starter over a bit. It needs 5 passes of the magnet to complete sensor test, at which point the sensor light will go on solid.

Jim Senicka
Team Manager, GrandRC Flight Team

PM  EMAIL  GALLERY  Attn:RR  Quote
09-02-2009 12:02 AM  8 years agoPost 3
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

Wait till you get to the blinking lights to set the RPM

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
09-02-2009 01:32 AM  8 years agoPost 4
Chief_USN

rrKey Veteran

Chesapeake, VA

My Posts: All  Forum  Topic

I like that feature on the GV-1 but it really isn't needed to setup a gov. What I do is (depending on the type of bird) I take my six inch steel rule which is approx 1 - 1.5mm thick. I place that in between the magnet and the sensor and tighten everything up. One, they won't touch unless your sensor comes loose, and two, the RL's require a max of 3mm clearance. your at 1.5mm. If you have a 600N like I do, just mount the engine with no shroud and set the distance and tighten everything up. Take engine back out and add the shroud. FYI, some imagination is required to mount the RL sensor on the 600N since the magnet has to pass the sensor perpendicular.

Chad

Team HeliProz 12-14
US Navy Chiefs...Unity, Service, & Navigation to the Fleet since 1893

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-02-2009 05:32 AM  8 years agoPost 5
jesus1895

rrApprentice

Tucson AZ

My Posts: All  Forum  Topic

ok.

but what is th etarget rpm for a raptor 50 hyper os.85/10 gearing,im thinking
about 2000 head speed......so what engine rpm will i be running on the RL?.thx

AMA #224344

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-02-2009 06:18 AM  8 years agoPost 6
jesus1895

rrApprentice

Tucson AZ

My Posts: All  Forum  Topic

better yet.

whats the formula for getting your engine rpm?...thx

AMA #224344

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-02-2009 12:02 PM  8 years agoPost 7
jsenicka

rrProfessor

Eagle River, WI

My Posts: All  Forum  Topic

head speed x gear ratio.
2000 x 8.5 = 17000
On RL10 that is 14k base mode plus 2k + 1k lights on

Jim Senicka
Team Manager, GrandRC Flight Team

PM  EMAIL  GALLERY  Attn:RR  Quote
09-05-2009 10:06 PM  8 years agoPost 8
jesus1895

rrApprentice

Tucson AZ

My Posts: All  Forum  Topic

next question

the RL sensor .i plugged it into my gv-1.most of the time the gv-1 displays 50 %....when the magnet gets to the sensor.it goes as hi as 85%,no higher..will that work,or no?.or should i wait till i get my genuine gv sensor?

AMA #224344

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-05-2009 10:17 PM  8 years agoPost 9
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

You can't use a RL sensor with a GV1

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
09-05-2009 10:20 PM  8 years agoPost 10
jesus1895

rrApprentice

Tucson AZ

My Posts: All  Forum  Topic

Didnt think so.but

I have noticed BH is one VERY smart dude!..kinda like a walking heli guru....wish i lived closer to you.
But i do have a flying buddy i work with.VERY smart also,but we both been away for a long while....going out ALL DAY monday......thanks again BH.

AMA #224344

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-05-2009 10:24 PM  8 years agoPost 11
jesus1895

rrApprentice

Tucson AZ

My Posts: All  Forum  Topic

What about the......

spktm backing plate sensor........i heard somewhere,there is a website the sells a backing plate sensor that will work with the GV-1....?Got a link anyone???

AMA #224344

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 346 views
HelicopterRadio - Servo - Gyro - Gov - Batt › help with revlock 10***PLZ***
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Wednesday, December 13 - 9:16 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online