RunRyder RC
 0  Topic Subscribe
WATCH
 1 page 362 views
Scorpion Power Scorpion Power
HelicopterAlignT-REX 600N › JR 8103 and NER 649 Setup on 600N
03-21-2009 02:20 AM  8 years agoPost 1
BlackHawk9

rrNovice

Toronto

My Posts: All  Forum  Topic

I've been trying to get my servos plugged into the right sockets on the NER 649 rx and so far its fine, the throttle, rudder work great. The aeileron, elevator and pitch work fine in terms of up and down, but left to right or front to back is reversed...

i'm not sure what i'm doing wrong but I've gone by the Align manual and they say you can switch the aeileron and pitch either way but I've done that and its just the same problem...

anyone can point out what i'm doing wrong...i'd truely appreciate it!

Do just once what others say you can't do, and you will never pay attention to their limitation

PM  EMAIL  GALLERY  Attn:RR
03-21-2009 02:27 AM  8 years agoPost 2
baddynergy

rrElite Veteran

sierra madre, ca-​usa

My Posts: All  Forum  Topic

Go to the swash menu and reverse the values from positive to negative.

Ie. ele +60 then revers it to -60
ail +60 then reverse to -60
Now if they are already negative numbers then switch to positive.

**Unattended children will be givin a shot of espresso and a puppy**

PM  EMAIL  GALLERY  Attn:RR
03-21-2009 02:39 AM  8 years agoPost 3
BlackHawk9

rrNovice

Toronto

My Posts: All  Forum  Topic

thank you, that's what i was looking for but now if i move the stick left the swash plate tilts right and stick right tilts the swash left. But it goes up and down and tilts front to back with the stick normally....

servo setup as follows:

front left servo: plugged in as Pitch
front right servo: plugged in as aileron
rear servo: plugged in as elevator.

NER S649 rx with DS821 digital servos

Ch 1 - Throttle
Ch 2 - aileron
Ch 3 - Elevator
Ch 4 - Rudder
Ch 5 - Gear
Ch 6 - Aux 1 aka Pitch
Ch 7 - Aux 2 gyro control
Ch 8 - Aux 3
Ch 9 - Aux 4

Do just once what others say you can't do, and you will never pay attention to their limitation

PM  EMAIL  GALLERY  Attn:RR
03-21-2009 02:49 AM  8 years agoPost 4
baddynergy

rrElite Veteran

sierra madre, ca-​usa

My Posts: All  Forum  Topic

then you need to reverse your ail setting.

Everything else looks good.

Just an FYI. Spektrum and JR have said that the 821 servo is not suitable for use in a 50size and up nitro heli. THere have been MANY reported failures of these servos. I would hate to see you have an expensive crash because of them.

**Unattended children will be givin a shot of espresso and a puppy**

PM  EMAIL  GALLERY  Attn:RR
03-21-2009 04:06 AM  8 years agoPost 5
BlackHawk9

rrNovice

Toronto

My Posts: All  Forum  Topic

let me try that setting, I won't be doing any 3D for now, just hovering getting used to the heli simple stuff until i find a comfort zone then upgrade to something better. What servos would you recommend?

Thanks for the tip =D love this forum everyone looks out for eachother!

Do just once what others say you can't do, and you will never pay attention to their limitation

PM  EMAIL  GALLERY  Attn:RR
03-21-2009 06:40 AM  8 years agoPost 6
BlackHawk9

rrNovice

Toronto

My Posts: All  Forum  Topic

sweet, got it setup correctly! Thanks man, appreciate all your help!

Do just once what others say you can't do, and you will never pay attention to their limitation

PM  EMAIL  GALLERY  Attn:RR
WATCH
 1 page 362 views
Scorpion Power Scorpion Power
HelicopterAlignT-REX 600N › JR 8103 and NER 649 Setup on 600N
 Print TOPIC  Make Suggestion 

 0  Topic Subscribe

Friday, November 24 - 12:21 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online