RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 1009 views
Scorpion Power Scorpion Power
Helicopter
e-
Minicopter
Joker › Maxi-Joker 2 Futaba 14MZ Swash settings?
03-18-2009 01:05 AM  8 years agoPost 1
sixstringlz

rrNovice

Hillsboro, OH. USA

My Posts: All  Forum  Topic

I have been trying to transfer my settings over from my 9C to my 14MZ and I'm not having much luck. Could someone please give me which swash type to pick and the swash mix numbers to help me get started.

I have it setup for the 120 swash. I can get the elev. and alir. sevros moving in the right direction with the swash mix numbers. But when I move the collective the left servo looking from the back of the heli is the only one that moves and it will not move when I give alir. input??? Tried reversing the servos, but it didn't help.

Thanks for your help!

PM  EMAIL  GALLERY  Attn:RR
03-18-2009 01:53 PM  8 years agoPost 2
Notar

rrKey Veteran

Taxachussetts

My Posts: All  Forum  Topic

Does not sound like you have the correct swash type set in the menu. It should be 3-120, and may be SR3, but i am not a futaba guy, perhaps someone else can tell you.
After you get the proper swash setting, use servo reverse to get all the servos going the correct way for collective pitch. Then check cyclic movements, and if backwards, reverse the percentage of that function in the swash menu, but do not use servo reverse.
Joe

PM  EMAIL  GALLERY  Attn:RR
03-18-2009 09:43 PM  8 years agoPost 3
sixstringlz

rrNovice

Hillsboro, OH. USA

My Posts: All  Forum  Topic

I have it set to HR3(120), there is no SR3 on the 14mz, but there is on my 9c and it works perfect on it, with the servos plugged into the some places?

PM  EMAIL  GALLERY  Attn:RR
03-18-2009 10:20 PM  8 years agoPost 4
Notar

rrKey Veteran

Taxachussetts

My Posts: All  Forum  Topic

Ok, one servo plugged into the collective channel, one into the aileron channel, and one into the elevator channel. That should work all the servos. If they are not all moving for collective, you may have the servos plugged in wrong, if you can get them all to move using fore and aft or left and right cyclic.
Joe

PM  EMAIL  GALLERY  Attn:RR
03-18-2009 10:35 PM  8 years agoPost 5
sixstringlz

rrNovice

Hillsboro, OH. USA

My Posts: All  Forum  Topic

I can get the elevator, and aileron moving correctly but with collective only one moves, tried switching up the config but don't seem to get any closer?

PM  EMAIL  GALLERY  Attn:RR
03-19-2009 02:48 AM  8 years agoPost 6
sixstringlz

rrNovice

Hillsboro, OH. USA

My Posts: All  Forum  Topic

Got it, I was using the 14 channel rx and I didn't have all three servos together for the packet thing to work. Thanks everyone for your help!

PM  EMAIL  GALLERY  Attn:RR
WATCH
 1 page 1009 views
Scorpion Power Scorpion Power
Helicopter
e-
Minicopter
Joker › Maxi-Joker 2 Futaba 14MZ Swash settings?
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Sunday, November 19 - 12:38 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online