RunRyder RC
 4  Topic Subscribe
WATCH
 1 page 521 views POST REPLY
Scorpion Power Scorpion Power
HelicopterMiniature Aircraft Whiplash & Fury 55 › Bearing part numbers tight shaft?
07-13-2008 04:33 PM  9 years agoPost 1
lfalsetto

rrKey Veteran

COLORADO

My Posts: All  Forum  Topic

I have been looking for the bearing part numbers for the extreme. I can't find them anywhere. Anybody have a bearing cross reference chart? I have about 6 shafts I purchased for spares. I do not remember them being this tight. I mean they are so tight that I have to tap them in and have a hard time removing them without a puller. Have I missed something?

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
07-13-2008 07:10 PM  9 years agoPost 2
Chris Ballard

rrApprentice

pensacola

My Posts: All  Forum  Topic

http://www.miniatureaircraftusa.com...t_documents.asp

go to the reference guide and get them from there.

if your gonna go.....go all out!

PM  EMAIL  GALLERY  Attn:RR
07-13-2008 08:09 PM  9 years agoPost 3
shawgl

rrKey Veteran

Murrieta, CA

My Posts: All  Forum  Topic

Go to the Bocca bearings site. They have a kit that has them all listed.
http://www.bocabearings.com/main1.a...38&n=*H45-07BSP
Greg

In God we trust, everyone else we monitor.

PM  EMAIL  GALLERY  Attn:RR
07-14-2008 12:17 AM  9 years agoPost 4
lfalsetto

rrKey Veteran

COLORADO

My Posts: All  Forum  Topic

What I am really looking for is the main shaft bearing sizes. I want to replace them with Boca bearings. I have a ton of other bearings

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
07-14-2008 12:49 AM  9 years agoPost 5
NewHeli

rrKey Veteran

Pittsburgh, Pennsylvania, USA

My Posts: All  Forum  Topic

I'm wondering this too...for a stratus though. The bearings are not listed anywhere in the manual Along with other common parts, like tail gears (the old plastic ones anyways) and the tail shaft, etc...)

I believe they're 10x19x5 can anyone confirm?

Nathaniel

Nathaniel Rice
Team YS Engines

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
07-14-2008 12:57 AM  9 years agoPost 6
lfalsetto

rrKey Veteran

COLORADO

My Posts: All  Forum  Topic

Thanks for the post NewHeli, I know the bearings are the same for the stratus. I have 3 but I want to go to the Boca bearings. In the kit it lists 10 mm bearings but a total of 5, 4 one size and 1 other that are all 10 mm. I may just order them directly.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
07-14-2008 12:57 AM  9 years agoPost 7
kthane

rrVeteran

Pensacola

My Posts: All  Forum  Topic

Confirmed.

PM  EMAIL  GALLERY  Attn:RR
07-14-2008 01:05 AM  9 years agoPost 8
NewHeli

rrKey Veteran

Pittsburgh, Pennsylvania, USA

My Posts: All  Forum  Topic

So they are 10x19x5's?

Nathaniel

Nathaniel Rice
Team YS Engines

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
07-14-2008 01:44 AM  9 years agoPost 9
kthane

rrVeteran

Pensacola

My Posts: All  Forum  Topic

yes

PM  EMAIL  GALLERY  Attn:RR
07-14-2008 01:53 AM  9 years agoPost 10
shawgl

rrKey Veteran

Murrieta, CA

My Posts: All  Forum  Topic

For future refereance, if you email bocca bearings and tell them what you are looking for they can tell you the size of the bearing in question. Especially since they have taken the time to make a "kit" for all the bearings included in the heli.

The link I attached in my first post is the kit fot the Fury Extreme and it is the same bearings for the stratus.

In God we trust, everyone else we monitor.

PM  EMAIL  GALLERY  Attn:RR
07-15-2008 04:20 PM  9 years agoPost 11
lfalsetto

rrKey Veteran

COLORADO

My Posts: All  Forum  Topic

I contacted MinAir and they said that they should be tight but maybe I have some oversized shafts. Dr Ben could you jump in on this. I know tight is good but this is really strange.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
WATCH
 1 page 521 views POST REPLY
Scorpion Power Scorpion Power
HelicopterMiniature Aircraft Whiplash & Fury 55 › Bearing part numbers tight shaft?
 Print TOPIC  Make Suggestion 

 4  Topic Subscribe

Friday, September 22 - 8:57 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online