RunRyder RC
 5  Topic Subscribe
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 1277 views POST REPLY
Scorpion Power Scorpion Power
HelicopterSynergy R/COther › What is the latest kit spec......
05-15-2008 12:15 AM  9 years agoPost 21
inkspot1967

rrProfessor

Cranston Ri

My Posts: All  Forum  Topic

yes i can. i still have some invisible pussyless header tanks on sale now for $7.99 shipped

but for you bud they are $35.99 plus $50.00 shipping.......

how many do you need......

PM  EMAIL  GALLERY  Attn:RR
05-15-2008 12:50 AM  9 years agoPost 22
Droid

rrElite Veteran

Deep down in the Southwest- UK

My Posts: All  Forum  Topic

Well at least 86, at that price it's a steal!!

Would you consider combining shipping? I'm not tight just thinking of the environment

Quotes may have been changed for my own amusement

PM  EMAIL  GALLERY  Attn:RR
05-15-2008 12:52 AM  9 years agoPost 23
inkspot1967

rrProfessor

Cranston Ri

My Posts: All  Forum  Topic

sure i can fit as many as you want in one little box......

PM  EMAIL  GALLERY  Attn:RR
05-15-2008 01:01 AM  9 years agoPost 24
Droid

rrElite Veteran

Deep down in the Southwest- UK

My Posts: All  Forum  Topic

Your ingenuity astounds me, how about sending it by "fresh air" mail??

Quotes may have been changed for my own amusement

PM  EMAIL  GALLERY  Attn:RR
05-15-2008 01:09 AM  9 years agoPost 25
inkspot1967

rrProfessor

Cranston Ri

My Posts: All  Forum  Topic

how about i do this either fresh air priority mail $50.00

or your choose of

old man crusty toe nail clippings mail for $30.00

or

stinky old man fart smelling with crusty toe nail air mail free of charge

im here to please....

PM  EMAIL  GALLERY  Attn:RR
05-15-2008 09:14 AM  9 years agoPost 26
RotorHead486

rrKey Veteran

England

My Posts: All  Forum  Topic

Hey crdhelipad,

On both my synergy's the star locking washer was not a very good fit on the brass bushing, i've since replaced with the starlock washer below which is a much better fit on the bushing and it takes quite a bit of force to punch it onto the bushing and you can see it dig into the brass, so this washer is doing what it's supposed to do.

You can get them from most Engineering suppliers, i got some 8mm ID starlock washers and they were spot on.

I've also done a dual radial bearing mod the tail rotor assembly aswell which seems to be working out great see below:

Using a Thrust race upgrade from QuickUK and an extra radial bearing i have modified the tail rotor to use two radial bearings and a single thrust race.

What i have done is replace the original thrust race with a radial bearing which provides more support and a much smoother operating tail than the original and then using the thrust race upgrade kit from QuickUK added to the hub which basically extend's the hub.

This thrust race upgrade was orignally used as an upgrade for the QuickUK CNC Alloy tail rotor assy for the raptor series but the thrust race and hub extension are perfect diameter for the Synergy hub.


Below you can see the hub extension upgrade in place:

Below you can see the complete thrust bearing upgrade in place:

This is basically a simple modification, the only area requiring any work is to relieve the blade grip where the thrust race is going to go as generally tail blade grips have a slight step in them to allow for free rotation of the thrust race, the synergy grips do not have this and this has been one of the contributing factors in the failures of the tail rotor assemblies. What i did was to install a bearing (old one if available) and then using either a file or Dremel which i used with a file tip, file away the area where thr thrust race is going to be. If you install a bearing and allow the tip of the dremel to run on it you will only be relieveing the area that is required be the thrust race and the area for the radial bearing stays tight.

I have not had enough time on the mod'd tail assy yet so only time will tell. But if any of you want to give it a go and let me know how you find it, please feel free.

Update:I've been flying the Mod for a few months now and so far it seems to holding up well, no changes needed to gyro settings etc...

Hyperformance Hyperbar 4mm Flybar conversion:
I flew with the 5mm flybar for a while and i liked it, the rotor head was solid but you could tell the flybar caused drag and slowed the head down, changing to the 4mm flybar allowed me to run 95mm VPaddles and instantly the way the heli flew changed, much more responsive and positive aswell.

Does shaky like you would not believe!!

Cheers!
Rossco

One Reason For Crashing'Rogue Servo Bent on World Domination'!!
FLP Flight Team

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 1277 views POST REPLY
Scorpion Power Scorpion Power
HelicopterSynergy R/COther › What is the latest kit spec......
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Tuesday, September 19 - 4:05 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online