RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 520 views POST REPLY
Scorpion Power Scorpion Power
HelicopterRadio - Servo - Gyro - Gov - Batt › futaba 611 creeping?
09-15-2007 03:23 AM  10 years agoPost 1
Tony Whiteside

rrKey Veteran

Shepherdsville, KY US

My Posts: All  Forum  Topic

i have a brand new 611 set up and i cant get to stop creeping just sitting on the table whats up with that? Help please drivin me crazy
Tony

PM  EMAIL  GALLERY  Attn:RR
09-15-2007 04:09 AM  10 years agoPost 2
pH7

rrKey Veteran

Sterling Heights, MI - USA

My Posts: All  Forum  Topic

How does it creep if it is sitting on the table? You cannot tell what a Heading Hold gyro will do by observing the tail rotors when it is sitting on the bench.

PM  EMAIL  GALLERY  Attn:RR
09-15-2007 04:38 AM  10 years agoPost 3
Tony Whiteside

rrKey Veteran

Shepherdsville, KY US

My Posts: All  Forum  Topic

611

its on a stratus and the servo wheel is creeping clock wise towards the tail very slowly and it does it in flight changed the tape ect.

PM  EMAIL  GALLERY  Attn:RR
09-15-2007 12:04 PM  10 years agoPost 4
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

Revo mix?

Different trims in different flight modes on your rudder maybe?

It will flash a square on the lcd if its getting an input.

Also moving it while it initializes will probably do that as well.

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR
09-16-2007 05:45 AM  10 years agoPost 5
Sky Dancer

rrVeteran

Bryan, Texas

My Posts: All  Forum  Topic

611 Creeping

I've found some transmitters are slightly off center on the Rudder channel. To solve this problem just add a little rudder sub-trim to correct the creeping. If the sub-trim does not fix the problem, try a different sensor.

Some sensors will drift with temperature changes.

Keep up your rotor speed !

PM  EMAIL  GALLERY  Attn:RR
09-16-2007 11:51 AM  10 years agoPost 6
MattJen

rrElite Veteran

UK

My Posts: All  Forum  Topic

deleted

All The Best

PM  EMAIL  GALLERY  Attn:RR
09-17-2007 12:21 AM  10 years agoPost 7
Tony Whiteside

rrKey Veteran

Shepherdsville, KY US

My Posts: All  Forum  Topic

ok guys thanks

i will try all of the above and mattjen are you taking about the menue box to the gy
Tony

PM  EMAIL  GALLERY  Attn:RR
09-17-2007 06:27 PM  10 years agoPost 8
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

No.

TRK (Tracking) has zero, NADA, nothing to do with drift off center when the gyro is at rest.

TRK is used to adjust out the presence of bounce at the end of left and right piros.

Look at the gyro amplifier's screen. There is a black LCD block on the screen that will go on and off as you move the rudder stick back and forth off center. Note the presence or lack thereof of that block when the stick is deflected. If the block stays the same when the stick is at center as it was when you moved the stick away from center, the the neutral signal of the rudder channel is off. You'll need to subtrim the rudder channel to find the perfect electronic center. Though some gyros out there will creep off center when the model is at rest on the bench, GY series gyros should not do this.

Ben Minor

PM  EMAIL  GALLERY  Attn:RR
WATCH
 1 page 520 views POST REPLY
Scorpion Power Scorpion Power
HelicopterRadio - Servo - Gyro - Gov - Batt › futaba 611 creeping?
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Friday, September 22 - 5:26 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online