RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 471 views
Scorpion Power Scorpion Power
HelicopterEngines Plugs Mufflers Fuel › Engine Quits in Midair
08-11-2007 04:42 PM  10 years agoPost 1
rudyy

rrElite Veteran

E. Amherst, NY

My Posts: All  Forum  Topic

My OS50SXH quits in mid air, and I am lucky to auto the heli safely in one piece. When I fire it up again, the engine starts up with no problem, but as soon as I remove the glow plug ignitor, the engine quits. Is the glow plug gone bad?

Rudy

PM  EMAIL  GALLERY  Attn:RR  Quote
08-11-2007 05:43 PM  10 years agoPost 2
jetranger

rrVeteran

PERHAM M.E.

My Posts: All  Forum  Topic

motor

Either too rich or bad plug or too lean in midrange

PM  EMAIL  Attn:RR  Quote
08-11-2007 08:48 PM  10 years agoPost 3
helinutz2

rrApprentice

Medicine Hat, AB​Canada

My Posts: All  Forum  Topic

Check your rear bearing. I had a similar situation this week with flameouts and found the rear brg was toast, after checking out the usual items (fuel lines, air leak, carb debris, etc)

Good Luck!
Gregg

Rave 90 ENV / Radikal E640 / Rush 750 / Trex 600N
Team No WhinerS, Team Renegade R/C Heliflyers

PM  EMAIL  GALLERY  Attn:RR  Quote
08-11-2007 09:32 PM  10 years agoPost 4
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

Yes, assuming it was running OK for awhile and this behavior just started, there's a good chance your rear bearing is starting to fail. Small bits of metal flake off the inner and outer races and find their way to the glow plug.

A plug fouled with bits of metal will start and run, but generally the motor will quit when you remove the battery, or it may run until you get to about 1/4 - 1/3 throttle, at which point it just quits.

Changing the plug can seem to make things better for awhile till another bit of metal finds its way to the plug.

Remove the motor, disassemble it, and inspect your rear bearing closely. Also inspect the piston skirt for scratches, the crown of the piston for dents or pits, and the inside of the cylinder head for dents or pits.

I recently replaced the bearings as well as the piston and ring in one of my OS 50s after it flamed out in mid air. The bearing was indeed bad, and under a microscope, I saw bits of stainless steel embedded in the piston skirt (it was a stainless steel/ceramic ball bearing).

I caught the problem in time and that OS 50 SX-H runs as good as it did when it was new and just getting broken in.

-----

It's a good idea to wash out the innards of your muffler if the bearing has gone bad, as bits of metal that make it through the motor can get stuck there, to be sucked back into the motor at a later date, putting out the fire...

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
08-12-2007 07:25 AM  10 years agoPost 5
wrobijns

rrApprentice

Swalmen, the​Netherlands

My Posts: All  Forum  Topic

Check the plug as well.
See if it is distorted or a matt color

If it is then check your temperture after 30 secs of hovering.
You might be running too hot.

Walter Robijns, 3D rules !!!

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 471 views
Scorpion Power Scorpion Power
HelicopterEngines Plugs Mufflers Fuel › Engine Quits in Midair
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Friday, November 24 - 10:06 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online