RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 484 views
Helicopter
e-
Align
Other › SA Sevro Installation?
01-28-2007 02:49 PM  10 years agoPost 1
88Z51

rrNovice

wyoming mi.

My Posts: All  Forum  Topic

How the heck do you get the little plastic plates installed on the inboard sides of the front servos?

thanks.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 02:56 PM  10 years agoPost 2
slider46

rrProfessor

Ocala Florida

My Posts: All  Forum  Topic

I use a pair of hemostats to hold the little plastic "thingy" while I run the screw into it... Run a screw into the "thingy" before you try to install it too...

Tom..... No "D" flying....

PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 05:00 PM  10 years agoPost 3
baddynergy

rrElite Veteran

sierra madre, ca- usa

My Posts: All  Forum  Topic

Easiest way is to pull out your main shaft and top bearing block and use needle nose pliers to hold them. With that out of the way there is plenty of room....

**Unattended children will be givin a shot of espresso and a puppy**

PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 06:19 PM  10 years agoPost 4
88Z51

rrNovice

wyoming mi.

My Posts: All  Forum  Topic

Thanks,

I did'nt think there was an easy way, kinda a chezzy design. How about the Align ESC, how do you get that to work? I plugged it into the Rx and batt, it makes a beep then nothing, does'nt go into set-up mode or anything. Never had this much problems with the aircraft esc's. Perhaps it's a defective one.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 06:37 PM  10 years agoPost 5
TomRex

rrElite Veteran

West Palm Beach Join Date: 12-28-2005

My Posts: All  Forum  Topic

Try and reverse your throttle channel output

Ignorance is the absence of facts.Stupid is lacking the intellectual capacity to comprehend the fact

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-29-2007 04:35 AM  10 years agoPost 6
BikeNBoatN

rrVeteran

Santa Ana, CA USA

My Posts: All  Forum  Topic

If you're using HS65's, I just glue those little plastic nuts to the undersides of the servo mounting ears. Then insert the servos from the inside of the frame so that the only thing showing is the tops of the servo. Then just screw the mounting screws in. For the rear servo, you can either do the same way and put the screws in from the inside, or glue the plastic nuts to the inside of the frame so the screws go in from the outside.

Brent
Slow and Smooth 2-D Scale Flyer
AMA #35431

PM  EMAIL  GALLERY  Attn:RR  Quote
01-30-2007 05:40 AM  10 years agoPost 7
marc8090

rrElite Veteran

Long Island, N.Y.

My Posts: All  Forum  Topic

You can also gently stab the little plastic things with an X-acto knife and use the knife to hold them in place as you install the screws.

PM  EMAIL  Attn:RR  Quote
01-30-2007 04:20 PM  10 years agoPost 8
rky5

rrVeteran

Oak Hills california

My Posts: All  Forum  Topic

Wifes tweasers

PM  EMAIL  Attn:RR  Quote
01-30-2007 05:09 PM  10 years agoPost 9
MarksRC

rrApprentice

Wellington, FL

My Posts: All  Forum  Topic

I used 2mm nuts and bolts(socket heads), which was much easier.

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 484 views
Helicopter
e-
Align
Other › SA Sevro Installation?
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Saturday, December 16 - 4:35 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online