RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 803 views
Helicopter
e-
Mikado
Other › Some logo 10 3d advice please
01-23-2007 06:25 AM  10 years agoPost 1
rcmarty

rrVeteran

Penticton , B.C. CANADA

My Posts: All  Forum  Topic

Looking to try the logo 10 3d heli out. Been happy with my swift so far but looking for a bit more zip.

I plan on robbing the neu 1910/1.5y , ph45hv , meudsa 3a 5volt bec , 401 /9254 out of the swift for the logo.

I'll go the 3d over the deluxe because i want the carbon blades and the alum swash.

I also outfitting a trex600 right now with a neu 1910/1y and plan on using a 8 cell 3700 fp pack. I'd also like to use the same pack in the logo. Is the 1.5y going to be enough on 8 cells ? OR will it be best to get the 1910/1y on this one also ? Looking for a hot setup here. I'm not a 3d king but hope to be able to do more one day. Some reserve power for when i mess up and demand lots of power to plow my way out of it is what i'm looking for (poor collective managment)

Some general questions :

- Are the logo carbons in the kit good ?
- Alum motor plate needed for flexing ?
- Anyone using a 9650 for the tail ? (run all on 6volts)
- 9650's should be good for cyclic.
- Any other quirks out there for a logo 10 3d i should be aware of ?

Thanks for the help ,

Martin

What goes up will come down.... one way or another !

PM  EMAIL  HOMEPAGE  Attn:RR  Quote
01-23-2007 06:36 AM  10 years agoPost 2
maxpower097

rrApprentice

none

My Posts: All  Forum  Topic

Some general questions :

- Are the logo carbons in the kit good ? Their decent!

- Alum motor plate needed for flexing ? For hard 3D

- Anyone using a 9650 for the tail ? (run all on 6volts) Tried it and didn't work out. 9650 couldn't handle the torque

- 9650's should be good for cyclic. Yes they ROCK!!!!!

- Any other quirks out there for a logo 10 3d i should be aware of ? None you will love it and notice the higher quality then the swift.

As far as the motors post the kv ratings and I'll crunch the numbers for yah and make some pinion suggestions.

PM  EMAIL  Attn:RR  Quote
01-23-2007 01:13 PM  10 years agoPost 3
westbeach

rrApprentice

Abbotsford, British Columbia. Canada

My Posts: All  Forum  Topic

logo

Martin,

Not sure if you have heard this; but Mikado is releasing "4" new logos in February. Sounds very promising, but they have been very tight lipped about the new logos. Not even a spy picture has been seen! But with this new lines when they hit the market is really the question? There is a local vendor for all you logo needs. His name is Ken Lee @ RCFlighstore.com out of Vancouver. February is just round the corner, if you're not in a rush! Cheers,

Neal

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-24-2007 02:32 AM  10 years agoPost 4
rcmarty

rrVeteran

Penticton , B.C. CANADA

My Posts: All  Forum  Topic

Yeah , i bought my t600 from ken along with loads of other stuff, great guy to deal with.

I did some reading here last night and found out about the new logo's.

I think i might wait it out. What i reall want is a heli that is 3d capable that's bigger than a 450 and smaller than a swift, the logo 10 is a bit smaller bit not by much. Something to take to work and fly at lunch.

Martin

What goes up will come down.... one way or another !

PM  EMAIL  HOMEPAGE  Attn:RR  Quote
01-24-2007 03:22 AM  10 years agoPost 5
maxpower097

rrApprentice

none

My Posts: All  Forum  Topic

I believe all the new logo's will be 500mm blades and up. You may wanna look at the HDX500, 3dx500, and lepton. They all run 430mm blades.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 803 views
Helicopter
e-
Mikado
Other › Some logo 10 3d advice please
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Monday, December 11 - 4:11 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online