RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 486 views POST REPLY
Helicopter
e-
Align
Other › Trex600: Balancing FP 4900 with Hyperion LBA10, throttle curve, pinion, blades?
11-22-2006 10:04 AM  11 years agoPost 1
Logieberra

rrApprentice

Canberra, Australia

My Posts: All  Forum  Topic

Hey guys,

Just ordered a new Trex 600 kit, stock stuff with the FP 4900mah battery WHOOO HOOOOO!

Problem #1: the FP battery come with what looks like TP balancing tabs. The issue with this is that I have a Hyerion LBA10 balancer which does not mate with these tabs.
Does any one have any CRYSTAL CLEAR instructions on how to make the tabs and Hyperion balancer compatible? I have spare balancing cables – all I need is the right wiring diagram as I understand the Hyperion and Flight Power have balancing leads that are opposite or something. I don’t want to get this stuff wrong!

Desired setup:
I don’t do 3D, just smooth circuits and cruising about with the view of keeping the packs and motor cool – I want this pack to last!

Questions:
1. I am unsure of what pinion will come with the motor, and if they provide more than one what should I run for this desired setup?

2. What throttle curve should I run in governor mode (again for a smooth/cool setup), as I have read that some guys are running 100% across the line – but is this not wrong as it gives the ESC no room to adjust - according to previous posts on Kontronik ESC’s?

3. Balancing: I will balance the packs before charging, during charging and once charged, then perhaps once more at the field.
Is this the best practice or overkill?

4. Align Blades: I’ll be using their new white carbon blades…are they nice?
I opted for the cheaper pair ($20.00AUD less than the CF).
http://www.align.com.tw/shop/produc...roducts_id=1463

5. I have two different types of loctites:
243 Loctite Threadlocker (blue stuff)
TL262 Champion Thread Lock (red stuff, thinner, like the stuff align give in trex 450 kits).
Any recommendations here?

Any general build tips/recommendations would be greatly appreciated!

Looking forward to the build!

Tip of the Day: ADDICTION? "Buy Align case, lock it up, hand over key."

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-23-2006 12:41 AM  11 years agoPost 2
Phil.L

rrApprentice

Australia

My Posts: All  Forum  Topic

10 tooth usually comes with the kit, 10 tooth is fine for putzing around.

not recomended to use the governor function, you would need to experiment with the throttle curves to the way you like it, but start off with the basic 0,25,50,75,100, and go from there, for idle up, 100,95,90,95,100 may work well for you. For 3d 100 flat is best.

You can just use the balancer while your charging, place the balancer in between the pack and the charger.

I havent used the Align blades yet (mine are in the mail), but they should be fine.

243 loctite all round on metal to metal parts in fine.

have fun,

http://www.rotortips.net/ <b> OutRage Batteries <b> G5

PM  EMAIL  HOMEPAGE  Attn:RR  Quote
WATCH
 1 page 486 views POST REPLY
Helicopter
e-
Align
Other › Trex600: Balancing FP 4900 with Hyperion LBA10, throttle curve, pinion, blades?
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Friday, April 20 - 2:24 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online