RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 452 views POST REPLY
Scorpion Power ProModeler
HelicopterThunder TigerOther › Are these ok servo's for my 90
03-06-2006 04:34 PM  11 years agoPost 1
PsychoZ

rrApprentice

Northern, CA

My Posts: All  Forum  Topic

Futaba 9252's, are these ok to use, here are the specs. 91.6 oz-in. 0.14 sec/60°. I am not flying any 3d, it is just pure hovering and foward flight. Nothing really exciting.

PM  EMAIL  GALLERY  Attn:RR
03-06-2006 04:57 PM  11 years agoPost 2
Peefor

rrVeteran

Norfolk UK

My Posts: All  Forum  Topic

They are good enough for my two 90 Furies, and also the Rappy 50's. Use the appropriate tail servo though, something a bit faster i.e. 9254 or 9251/6.

Your flying might be exiting if you get a duff servo.

Pete

PM  EMAIL  GALLERY  Attn:RR
03-06-2006 05:01 PM  11 years agoPost 3
DrDan

rrVeteran

Potosi, Missouri

My Posts: All  Forum  Topic

Need to know a little more about your setup.

They should be ok for the cyclics, but I would go for something with a little more torque for collective (for peice of mind), and something with a little more speed on throttle.

They would be ok all around for hovering and forward flight, but if you get into any harder stuff, go with the above advice. My thoughts are if you are getting it now, you might as well buy the right stuff so you wont have to upgrade later, concerning the servos that is. It may only cost you a few bucks more.


Dr. Dan

PM  EMAIL  GALLERY  Attn:RR
03-06-2006 05:47 PM  11 years agoPost 4
PsychoZ

rrApprentice

Northern, CA

My Posts: All  Forum  Topic

I've actually had this heli since June 04' new in the box but when my wife got breast cancer I put everything aside, but now that she has finished all the chemo and is making a full recovery I can get back into my hobbies. What I have is a 90SE, YS91, GY401 w/ 9253, and I had (2) 9252, so I need 2 more servo's to finish off my bird. And since I haven't flown in 1-1/2 years I know I am starting off fresh, when I had my 30 I was still learning forward flight. Basically I am a born again newbie with a big bird, and boy is it big, I am still amazed at how big it is, she is so beautiful. I even had a custom Arizona Heli canopy made for it.

If you have ideas for where to put my servos let me know, I figured I would use one of the 9252's for the throttle. Or should I use hem for the cyclics. Any help would be greatly appreciated, it has been so long I feel like I am starting all over from sctrach.

Thanks in advance for any assistance, and if anyone is in the Sacramento area and wouldn't mind looking over my 90, plese speak up.

PM  EMAIL  GALLERY  Attn:RR
03-06-2006 05:50 PM  11 years agoPost 5
blakka_1

rrElite Veteran

London/Enfield

My Posts: All  Forum  Topic

If your not into 3d then those servos will be fine, more than good enough.

PM  EMAIL  Attn:RR
WATCH
 1 page 452 views POST REPLY
Scorpion Power ProModeler
HelicopterThunder TigerOther › Are these ok servo's for my 90
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Thursday, August 24 - 9:42 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online