RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 484 views
Scorpion Power Scorpion Power
10-09-2005 07:47 PM  12 years agoPost 1
new sceadu

rrVeteran

LEICSTERSHIRE

My Posts: All  Forum  Topic

Hi
How do i get my JR tx (set to ppm) to work on my V3, I have a good set of matching crystal but only get red/green flashing on the RX and no control, I have tried reversing throttle channel and putting trim to the bottom and top.Still get nothing, It all works fine on the kit TX

Thanks
Matt

PM  EMAIL  GALLERY  Attn:RR  Quote
10-09-2005 07:50 PM  12 years agoPost 2
cudaboy_71

rrElite Veteran

sacramento, ca, u.s.

My Posts: All  Forum  Topic

move your throttle trims down too and try that with reversing the channel.

just a guess. no reason it shouldnt work. i use a JR9303 on my V1.

if it ain't broke, break it.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-09-2005 08:02 PM  12 years agoPost 3
new sceadu

rrVeteran

LEICSTERSHIRE

My Posts: All  Forum  Topic

Hi
Yes i've tried that, trim down / sub trim down / channel reversed / Heli mode / ppm but still nothing??????

Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
10-10-2005 03:54 AM  12 years agoPost 4
MidStar40

rrApprentice

Sioux Falls, SD

My Posts: All  Forum  Topic

If you are trying to use your JR tx with the V3 4-n-1 module, it won't work. The module is negative shift, your tx is positive shift. The red/green flashing means no tx input.

Rod

PM  EMAIL  GALLERY  Attn:RR  Quote
10-10-2005 04:05 AM  12 years agoPost 5
cudaboy_71

rrElite Veteran

sacramento, ca, u.s.

My Posts: All  Forum  Topic

that very well could be the case, midstar.

i'm using a pha-01 (3 in 1) and a JR pico 4ch rx on my v1.

FYI, balsapr.com has the pha-01 on sale still if theyre still in stock; $30. plus you need a pico jr rx ~$20.

i know, more money; more money. this is a hobby. you should be used to that by now

if it ain't broke, break it.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-10-2005 04:19 AM  12 years agoPost 6
MidStar40

rrApprentice

Sioux Falls, SD

My Posts: All  Forum  Topic

I wonder if the Century 4n1 module is put together like the Blade CP 4n1. I've read a few posts of Blade owners hacking the 4n1 to get around the neg shift rx and adding a JR rx and still being able to use the Blades 2 esc's and gyro. That would only cost $20 for the JR rx.

Rod

PM  EMAIL  GALLERY  Attn:RR  Quote
10-11-2005 09:33 PM  12 years agoPost 7
new sceadu

rrVeteran

LEICSTERSHIRE

My Posts: All  Forum  Topic

Hi

I now have signal by using century rx crystal and JR tx crystal, I thought they had to both be the same as the TX but obviously i was wrong!

I now can get servo's / motors to work but they're all on the wrong channels,
i;e throttle is on elevator stick, i can't swap the wires in the 5 in 1 receiver as the motors only have 2 wires, Is this it now or can i do anything to get it right???

Thanks
Matt

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 484 views
Scorpion Power Scorpion Power
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Wednesday, November 22 - 1:14 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online