RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 763 views
Scorpion Power Scorpion Power
Helicopter
e-
Elec-Helicopters New or Limited Activity
Zoom › Heli hobby Aluminum bell crank with ball link
10-24-2004 03:20 PM  13 years agoPost 1
YZY

rrNovice

Singapore

My Posts: All  Forum  Topic

Any 1 used it?? how does it work does it help??

http://www.helihobby.com/html/zoom_400_upgrades.html

PM  EMAIL  HOMEPAGE  Attn:RR  Quote
10-24-2004 07:08 PM  13 years agoPost 2
Air_Screw

rrNovice

Fort Lauderdale, FL​USA

My Posts: All  Forum  Topic

I haven't tried hh's bellcrank, I went with with the bellcrank from sparrowproducts and I'm happy with it. However, I would have gone with a bellcrank from microheli.com if their's would have come out first.

Also, look at microheli's pitch slider if you haven't already upgraded it. My Shogun's tail is solid using microheli's gear case, sparrow's bellcrank, and a custom pitch slider.

Regards,

Air_Screw


PM  EMAIL  Attn:RR  Quote
10-25-2004 05:04 PM  13 years agoPost 3
YZY

rrNovice

Singapore

My Posts: All  Forum  Topic

no other reply??

PM  EMAIL  HOMEPAGE  Attn:RR  Quote
10-25-2004 08:15 PM  13 years agoPost 4
8AxleEd

rrApprentice

San Jose, CA

My Posts: All  Forum  Topic

I just ordered the Micro-Heli one.

I think you will be sorry if you order one from Hell-i-hobby.

http://www.modefosheli.com/zoom_sgn_upgrades?start=15

PM  EMAIL  Attn:RR  Quote
10-25-2004 09:06 PM  13 years agoPost 5
CRAZYKEV

rrVeteran

Cincinnati,Oh -​U.S.A.

My Posts: All  Forum  Topic

I do have the entire microheli ball bearing pitch slider and ball bearing bell crank and can tell you there is not a hint of play in this setup. It is way slick man! You can use the stock slider and get the bell crank assembly which comes with a machined ball that is pressed and glued( It will not come off even if you wanted ) onto the stock pin on slider. Then later you can upgrade to the pitch slider SE which has this machined ball. This whole setup is bad ass!

check it out: http://www.microheli.com

Kevin

PM  EMAIL  GALLERY  Attn:RR  Quote
10-25-2004 09:45 PM  13 years agoPost 6
Baracus

rrApprentice

Seattle,WA

My Posts: All  Forum  Topic

The HH Bellcrank for the H2 sucks...basically there is a lot of play in the ball/socket that the slider pin seats in on the Hornet 2 version.
You can use a small socket and light hammer taps to re-seat the ball in the enclosure, basically rolling more of the cup material over the ball to remove slop.
Not the most gracefull fix, but it worked for me.
Now the Zoom version doesn't appear to have this same ball / cup setup...so hopefully this issue is resolved. Let us know how it goes if you buy one.

Baracus

PM  EMAIL  Attn:RR  Quote
10-25-2004 09:58 PM  13 years agoPost 7
Gyronut

rrProfessor

Martinsville In.

My Posts: All  Forum  Topic

I admit that I actually bought one once and was shorted the ball link coupler.

I informed HH many times and my emails were never returned or answered.

The Bellcrank in question was a hunk -o- junk. The Ball was very loose and I had to mash it to get rid of the excess slop.....

Don't waste your time on this one. I was better off with the stock hornet bell crank...

Rick

PM  EMAIL  GALLERY  Attn:RR  Quote
10-26-2004 04:09 AM  13 years agoPost 8
YZY

rrNovice

Singapore

My Posts: All  Forum  Topic

ok thanks guys

PM  EMAIL  HOMEPAGE  Attn:RR  Quote
WATCH
 1 page 763 views
Scorpion Power Scorpion Power
Helicopter
e-
Elec-Helicopters New or Limited Activity
Zoom › Heli hobby Aluminum bell crank with ball link
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Saturday, November 18 - 8:22 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online