RunRyder RC
 6  Topic Subscribe
WATCH
 1 page 1554 views
HelicopterMain Discussion › Dyeing a Raptor Canopy with Rit color dye?
05-31-2004 03:48 PM  13 years agoPost 1
Flybyu2

rrNovice

Bradley, Illinois

My Posts: All  Forum  Topic

Can you dye a Raptor Canopy with the Rit dye like all other plastic white parts? I am insterested in doing this if it will work. Painting these canopys like I have done in the past takes time and sucks when finished. Any info will help.

Thanks,
Brian M.

PM  EMAIL  Attn:RR  Quote
05-31-2004 04:00 PM  13 years agoPost 2
Tom DeWinter

rrVeteran

Quad Cities, IL

My Posts: All  Forum  Topic

I've been thinking about this too, but I suspect that it will fail.

Hope to hear from someone who has tried it.

Tom

Quad Cities RC Whirlybirds -- FunFly July 12 & 13, 2008 Davenport IA
Plan Now to Attend!!!

PM  EMAIL  GALLERY  Attn:RR  Quote
05-31-2004 04:09 PM  13 years agoPost 3
Phranque

rrApprentice

Wherever you go, there you are.

My Posts: All  Forum  Topic

Haven't done it myself, but I don't see why not. You're just going to need something larger to hold enogh water to cover the canopy, and I would think you might want to use an extra pack of dye to get good color density. Anyway, if it does mess up, wash it real good, let it dry, and paint over it....

Flying a heli is like seeing the Matrix, it is a mind bending experience.

PM  EMAIL  GALLERY  Attn:RR  Quote
05-31-2004 04:51 PM  13 years agoPost 4
Pipeous

rrVeteran

Surrey, BC, Canada

My Posts: All  Forum  Topic

I tried to do my sceade evo canopy and it didn't take.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-31-2004 04:54 PM  13 years agoPost 5
Ted Toth

rrElite Veteran

Myrtle Beach S.C.

My Posts: All  Forum  Topic

take a scrape piece of the canopy
put it in hot water hot enough to make it curl
you want it hot but not enough to curl
mix in more dye than you think you need
weight it down check every ten minutes
good luck

.

You don't stop laughing because you grow old, you grow old because you stopped laughing.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-31-2004 09:15 PM  13 years agoPost 6
SteveH

rrProfessor

Texas

My Posts: All  Forum  Topic

I've done it and it works. Like Ted said, it needs to be in HOT water and thats a problem finding a pot that big. If you submerge parts of it at a time, you will get a splotcy line. Also, it will fade with time and fuel will make it fade.

I've found it much easier and more effective to flash it and then just paint it. Learn more about it here: http://runryder.com/helicopter/t873...highlight=torch

The government cannot give you anything without first taking it from someone else.

PM  EMAIL  GALLERY  Attn:RR  Quote
06-01-2004 03:24 PM  13 years agoPost 7
DrDan

rrVeteran

Potosi, Missouri

My Posts: All  Forum  Topic

Make sure that you add a good amount of salt to the water. I have done 2, and the darker the color, the better the results. One problem though is that when you heat up the canopy (NOT BOIL), it will shrink a bit. You should notice this when you try to attach the windshield to the canopy and the canopy to the mounts.

I have also dyed the fins, landing struts, and the canopy clip. They both dye very well. The only problem with the landing struts is that if you heat them up, the grub screw hole will weaken and split when you tighten the screw up. I did this, and ruined a strut. If you do dye them, you shouldn't heat up the water.

Another thig also is that fuel tends to make the dye come out, and it will make a mess. After you dye the struts, make sure you clear coat them with some fuel proof stuff.

Here are some pic's of my dye jobs. I dyed my canopy yellow, which won't show up to well.:




Dr. Dan

PM  EMAIL  GALLERY  Attn:RR  Quote
06-01-2004 10:17 PM  13 years agoPost 8
Linley

rrApprentice

Rockville Centre - LongIsland, New York

My Posts: All  Forum  Topic

How to make paint stick better to Plastic

Hello, I have experimented with a method of getting paint to stick substantially much better on plastic. Check my gallery for proof.

You may not believe this, but applying torch heat to the plastic will allow the molecules in the plastic to raise up like little hairs and better absorbe the paint. You will see in my gallery that I used 3 peices of Raptor 60 plastic material for this.

Plastic#1 - No Torch heat, and not sanded - but rubbed with alcohol to remove any finger oils. I used latex gloves.

Plastic#2 - Torch heat applied, not sanded, but rubbed with alcohol to remove any finger oils. I used latex gloves

Platic#3 - No Torch but sanded the plastic well- but rubbed with alcohol to remove any finger oils. I used latex gloves


As you can see in my gallery, the non-torched pieces flaked as I bent the material. I cannot get the paint to flake off the Torched Piece. I even applied an ice pick with resonable pressure and it won't scratch it. I even bent the plastic to its fullest and paint won't warp or flake off.

Let me know what you think. All 3 pieces were painted at the same exact time with the same amount of paint.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-01-2004 10:20 PM  13 years agoPost 9
trey3670

rrApprentice

colorado way up north

My Posts: All  Forum  Topic

what paint? iv tryed the "flashing" method you descibe and while it works,it still is not perfect,maybe i used the wrong paint though

PM  EMAIL  GALLERY  Attn:RR  Quote
06-01-2004 11:21 PM  13 years agoPost 10
archangel

rrApprentice

Pasadena, CA - USA

My Posts: All  Forum  Topic

I left a Nexus canopy in a bucket of dye once for over three weeks...

...it's still white.

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2005 01:12 PM  12 years agoPost 11
Top End

rrApprentice

Darwin

My Posts: All  Forum  Topic

Two week ends ago I dyed my canopy with RIT green full bottle of dye left in wash tub for 8 hours the water temp was 40c to start with, the dam thing came out The old Shuttle blue yes BLUE. with in those two weeks it faded to a light purple and still fadeing. where the clear part of the decals are it is still quite blue .The colour of it now and stickers still look good.
Basic over all colour starting to go spotty.
I do dye lots of plastic's but this is strange (polypropylene).

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1554 views
HelicopterMain Discussion › Dyeing a Raptor Canopy with Rit color dye?
 Print TOPIC  Make Suggestion 

 6  Topic Subscribe

Monday, December 11 - 7:10 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online