RunRyder RC
 3  Topic Subscribe
WATCH  1 page 325 views TOPIC CLOSED
ProModeler Scorpion Power
allns47

Key Veteran

Richmond IN.

My Posts: All  Forum  Topic

Can't figure this out....regardless of the setting the swash do Sent stay still when you spin heli?

01-28-2017 04:27 PM
PM  EMAIL  GALLERY  Attn:RR
Heli_Splatter

Key Veteran

Silver Spring, MD by way of Sidney, Ne - USA

My Posts: All  Forum  Topic

Google is your friend... lots of Youtube videos.

Watch at YouTube

01-28-2017 09:11 PM
PM  EMAIL  GALLERY  Attn:RR
allns47

Key Veteran

Richmond IN.

My Posts: All  Forum  Topic

I have goggled and I have seen this video but my swash is not doing what there's is

01-28-2017 09:34 PM
PM  EMAIL  GALLERY  Attn:RR
Heli_Splatter

Key Veteran

Silver Spring, MD by way of Sidney, Ne - USA

My Posts: All  Forum  Topic

It is difficult to guess what is going wrong without a video or other description. It could be that prior steps are causing this one to fail. You might try running through the entire setup once more.

More description of what the swash plate is doing during this step would help diagnose the situation.

01-29-2017 12:07 AM
PM  EMAIL  GALLERY  Attn:RR
allns47

Key Veteran

Richmond IN.

My Posts: All  Forum  Topic

Ok when I enter step n the swash tilts back...when i hold the heli by the rotor and spin the heli the from of the swash should stay up but as I start to spin it immediately drops...

01-29-2017 05:42 AM
PM  EMAIL  GALLERY  Attn:RR
Heli_Splatter

Key Veteran

Silver Spring, MD by way of Sidney, Ne - USA

My Posts: All  Forum  Topic

Lets say that the swash dips down to the south direction when you enter this function(direction does not matter). When the correct setting is selected, no matter what direction the helicopter points, the swash plate will always dip to the south.

If it is not, select another setting.

01-29-2017 03:12 PM
PM  EMAIL  GALLERY  Attn:RR
Richardmid1

rrProfessor

Leeds, England

My Posts: All  Forum  Topic

Yep the swash should tilt and hold that tilt in relation to which wall it is tilting towards and NOT in relation to the heli. If it's not simple flick the rudder stick to reverse it, there's only two options.

60% of the time, it works every time!

01-29-2017 04:46 PM
PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
allns47

Key Veteran

Richmond IN.

My Posts: All  Forum  Topic

I figured it out..thanks guy for your help

01-29-2017 06:00 PM
PM  EMAIL  GALLERY  Attn:RR
JuanRodriguez

Elite Veteran

The Villages, Florida

My Posts: All  Forum  Topic

Why not post the resolution to your problem so that others down the line can benefit ??

Been there, done that and old enough to know better.....

01-29-2017 09:33 PM
PM  EMAIL  GALLERY  Attn:RR
Richardmid1

rrProfessor

Leeds, England

My Posts: All  Forum  Topic

As I would get flamed for typing RTFM, here it is on page 18. It even has pictures.

N. Setting the Pirouette Optimization Direction.
1. Note the direction the swashplate tilts when entering menu point (N). The swashplate will tilt forward or back; the direction does not matter.
2. Hold the helicopter at the rotor head and spin the helicopter by hand around the main shaft.
3. The swashplate should remain in the same tilt direction regardless of the rotational direction of the helicopter.
4. If the swashplate changes direction and rotates against the direction of the helicopter, use the rudder stick to change the direction.
5. Push the setup button to save the selection and exit the Setup Menu (N)

60% of the time, it works every time!

01-30-2017 10:50 AM
PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
Heli_Splatter

Key Veteran

Silver Spring, MD by way of Sidney, Ne - USA

My Posts: All  Forum  Topic

I don't believe he was able to understand the directions. Though it seems simple enough, if you do not speak English or German, you may have trouble understanding. been there.

01-30-2017 12:13 PM
PM  EMAIL  GALLERY  Attn:RR
allns47

Key Veteran

Richmond IN.

My Posts: All  Forum  Topic

richard

Thanks.

01-30-2017 12:13 PM
PM  EMAIL  GALLERY  Attn:RR
WATCH  1 page 325 views TOPIC CLOSED
Hitec RCD ProModeler
 Print TOPIC Advertisers 

 3  Topic Subscribe

Monday, February 20 - 3:23 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies