RunRyder RC
 2  Topic Subscribe
WATCH  1 page 154 views POST REPLY
ProModeler Scorpion Power
shiver

Senior Heliman

Ireland

My Posts: All  Forum  Topic

What's the diff between these two parts. They are both 12t pinions for 6mm shafts. Both are 14mm high. Mik4412 and mik4636. On the Mikado web it sais to use mik4636 with the the 106t mid 1 main gear. I've just installed mik 4412.

12-11-2016 01:23 PM
PM  EMAIL  GALLERY  Attn:RR
DemetriusUSN

Veteran

Virginia Beach, Va USA

My Posts: All  Forum  Topic


The 4635 is a 11 tooth pinion and 4412 is a 12 tooth pinion.

Minicopter Diabolo 700, Compass 7hv, Goblin 700 triblade, Compass 6hvu, Logo 600se, Goblin 570 triblade and Logo 400se

12-11-2016 02:38 PM
PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
shiver

Senior Heliman

Ireland

My Posts: All  Forum  Topic

Hi. Not 4635 but 4636. They both 12t pinions. Thanks

12-11-2016 02:43 PM
PM  EMAIL  GALLERY  Attn:RR
HilliHeli

Veteran

S.MI./FL.

My Posts: All  Forum  Topic

Mikado.de shows 04412 to be replacement for 04636 here ;
http://shop.mikado-heli.de/LOGO-Hel...7&c=7223&p=7223

!Antriebe, die bewegen!
Jazz', Jives & vbar's
Futaba FASST / FASSTest

12-11-2016 10:17 PM
PM  EMAIL  GALLERY  Attn:RR
DemetriusUSN

Veteran

Virginia Beach, Va USA

My Posts: All  Forum  Topic

My fault, sorry.

Minicopter Diabolo 700, Compass 7hv, Goblin 700 triblade, Compass 6hvu, Logo 600se, Goblin 570 triblade and Logo 400se

12-11-2016 10:37 PM
PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
shiver

Senior Heliman

Ireland

My Posts: All  Forum  Topic

Thanks. It seems that they replaced the part no to 4412 from 4636 as mentioned above. Is the pinion directional? Or can it be reversed. My grub screw is facing the motor but that leaves a big space to the CB bearing. Thanks guys .My first logo and first herringbone setup.

12-12-2016 03:48 AM
PM  EMAIL  GALLERY  Attn:RR
HilliHeli

Veteran

S.MI./FL.

My Posts: All  Forum  Topic

Sent you a PM with more info on spacing / shimming for the CB assembly.

!Antriebe, die bewegen!
Jazz', Jives & vbar's
Futaba FASST / FASSTest

12-12-2016 05:54 AM
PM  EMAIL  GALLERY  Attn:RR
shiver

Senior Heliman

Ireland

My Posts: All  Forum  Topic

Thanks a ton

12-12-2016 08:18 AM
PM  EMAIL  GALLERY  Attn:RR
HilliHeli

Veteran

S.MI./FL.

My Posts: All  Forum  Topic

I don't believe that shimming is needed for the end-of the motor's shaft that fits into the actual CB housing.
The shims shown in the "CB kit" look to be for adjusting the extended bracket that fits onto the Helis main-shaft (note ID / OD of shown shims).

http://shop.mikadousa.com/04622-Mot...-6mm_p_618.html

!Antriebe, die bewegen!
Jazz', Jives & vbar's
Futaba FASST / FASSTest

12-12-2016 09:41 AM
PM  EMAIL  GALLERY  Attn:RR
WATCH  1 page 154 views POST REPLY
ProModeler Scorpion Power
 Print TOPIC Advertisers 

 2  Topic Subscribe

Sunday, January 22 - 10:08 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies