RunRyder RC
 1  Topic Subscribe
WATCH  1 page 382 views POST REPLY
Scorpion Power AlignRC
Brokenlink

Elite Veteran

Oakdale,Ca.

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Checking to see if any interest in atlas 10" lathe.

Experience is a hard teacher,because she gives the test first,then the lesson afterwards

08-08-2016 09:24 PM
PM  EMAIL  GALLERY  Attn:RR
Danny Calderone

Key Veteran

South Jersey

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Nice little machines. They don't seem to bring much without the QCGB and some good chucks and accessories though.

Danny Calderone. AREA138

08-08-2016 10:28 PM
PM  EMAIL  GALLERY  Attn:RR
Brokenlink

Elite Veteran

Oakdale,Ca.

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Yup,kind of like a helicopter in some ways,they don't bring much without a motor or blades and electronics.But if you look real close there are two chucks sitting on the bed of the lathe,that's the two long skinny pieces of metal side by side.Also has a steady rest,tool post holder,lantern style and 4 position etc.

Experience is a hard teacher,because she gives the test first,then the lesson afterwards

08-09-2016 03:46 PM
PM  EMAIL  GALLERY  Attn:RR
Danny Calderone

Key Veteran

South Jersey

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Ahh. Only one picture loaded the first time I saw the post. I see the 3 & 4 jaw chucks now.

Danny Calderone. AREA138

08-09-2016 03:58 PM
PM  EMAIL  GALLERY  Attn:RR
Dan Minick

Key Veteran

Columbus, WI

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

I love to look, but I might buy with a price!

Roller bearings?
Any taper on long cuts?
Counter shaft in good shape?

Is this machine setup to do threading?

Team Synergy, Team FBL Rotors---Formerly Dyecocker1-------if its not broke...it will be!

08-14-2016 10:50 PM
PM  EMAIL  GALLERY  Attn:RR
Brokenlink

Elite Veteran

Oakdale,Ca.

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Yes timken roller bearings,lathe was used very little,tapers no problem,counter shaft excellent,power cross feed,pm me and we can talk I will give you a call and we can work out a price that will make us both happy,I just don't need 2 lathes.

Experience is a hard teacher,because she gives the test first,then the lesson afterwards

08-15-2016 04:48 PM
PM  EMAIL  GALLERY  Attn:RR
Brokenlink

Elite Veteran

Oakdale,Ca.

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Brady Maynard will get the lathe

Experience is a hard teacher,because she gives the test first,then the lesson afterwards

08-20-2016 07:54 PM
PM  EMAIL  GALLERY  Attn:RR
WATCH  1 page 382 views POST REPLY
Thunder Power RC ProModeler
 Print TOPIC Advertisers 

 1  Topic Subscribe

• CLASSIFIEDS HELP-FAQ Buyer beware! RunRyder cannot vouch for any seller's or buyer's credibility and will not accept responsibility for any transactions resulting from the use of this site.

Tuesday, December 6 - 12:08 pm - Copyright © 2000-2016 RunRyder   EMAILEnable Cookies