RunRyder RC
 2  Topic Subscribe
WATCH  1 page 331 views POST REPLY
AlignRC Scorpion Power
trumanmc

New Heliman

Terry, Ms USA

My Posts: All  Forum  Topic

I have a Futaba R617FS receiver and a Futaba 7c radio. On the "Trans" page everything centers correctly but I get no throttle movement on the bar.Collective moves normally.There are no mixes in the 7C Any ideas?
Thanks,
Truman

07-23-2016 09:35 PM
PM  EMAIL  Attn:RR
rcflyerheli

Key Veteran

Granbury, TX USA

My Posts: All  Forum  Topic

Not positive but it seems to me that your ESC should be plugged into the collective/esc plug in your vbar, rather than ch3 in either the Fut RX or on ch3 on the Vbar.

A couple years ago, I set up a buddy's Vbar with a Fut TX, and my recollection is that there was some obscure setting either in the throttle curve or somewhere else that needed to be changed to get everything going His was a nitro, rather than an electric, and I remember there were a couple oddball things I encountered, but on your electric your cyclic servos go into the ch 1-3 outputs on the Vbar, the tail servo goes to the tail output, and the esc goes to the coll/esc output.

Goblin 700, Trex 700DFC, Gaui X7, Logo 690SX, Logo 600SX;
Amain Team Rep

07-24-2016 04:31 PM
PM  EMAIL  GALLERY  Attn:RR
trumanmc

New Heliman

Terry, Ms USA

My Posts: All  Forum  Topic

On the receiver page of the V-BAR setup software is a picture of my exact receiver and that is how it is wired.The colle/esc port on the V-bar goes to ch6 on the receiver. Ch3 on the receiver is left open so I figured that is where the esc should be.I have tried numerous combinations and still can't get the bar to move. I tried mixing ch6 and ch3 in the transmitter also.
This is the video I have been using:

Watch at YouTube

Thanks
Truman

07-24-2016 06:16 PM
PM  EMAIL  Attn:RR
rcflyerheli

Key Veteran

Granbury, TX USA

My Posts: All  Forum  Topic

What number (channel) do you see in the box next to esc/throttle on your receiver tab in the software?

Goblin 700, Trex 700DFC, Gaui X7, Logo 690SX, Logo 600SX;
Amain Team Rep

07-24-2016 07:33 PM
PM  EMAIL  GALLERY  Attn:RR
trumanmc

New Heliman

Terry, Ms USA

My Posts: All  Forum  Topic

esc/throttle is on ch3 and collective is on ch6

07-24-2016 10:28 PM
PM  EMAIL  Attn:RR
rcflyerheli

Key Veteran

Granbury, TX USA

My Posts: All  Forum  Topic

Are you doing Sbus?

Goblin 700, Trex 700DFC, Gaui X7, Logo 690SX, Logo 600SX;
Amain Team Rep

07-24-2016 11:54 PM
PM  EMAIL  GALLERY  Attn:RR
HilliHeli

Veteran

S.MI./FL.

My Posts: All  Forum  Topic

T7C with R617FS RX. should be set-up as 7 CH FASST and use the "jumpers" to make connections between vbar and RX. (remember that R617FS is only FASST / non S-Bus type RX.).

Also,
I sent you a PM with the vstabi.de site links that should help you get everything wired correctly.
If you still have problems be sure to post back here (and with the specifics I asked for) and either I or someone else will get you sorted-out

!Antriebe, die bewegen!
Jazz', Jives & vbar's
Futaba FASST / FASSTest

07-25-2016 01:02 AM
PM  EMAIL  GALLERY  Attn:RR
newbheliusr

Senior Heliman

You guesss

My Posts: All  Forum  Topic

unless you're using the vbar gov the throttle will be in the rx. For standard throttle curves you just put the throttle in the rx and call it good. the throttle channel on the vbar isn't used.

07-25-2016 09:47 PM
PM  EMAIL  GALLERY  Attn:RR
WATCH  1 page 331 views POST REPLY
Thunder Power RC AlignRC
 Print TOPIC Advertisers 

 2  Topic Subscribe

Wednesday, September 28 - 6:05 pm - Copyright © 2000-2016 RunRyder   EMAILEnable Cookies