RunRyder RC
 4  Topic Subscribe
WATCH  1 page 390 views POST REPLY
AlignRC Thunder Power RC
Knud Pedersen

Key Veteran

Denmark - Europe

My Posts: All  Forum  Topic

Hi
Just got my CGY back from service - crashed with it because it was uncontrollable. But they did not find any failure on the unit.....

I have now updated it the V2 and installed it in a 450.

BUT when I tilt the helicopter (on the table) to side the swash plate/CGY does not counter steer - or at least I can see it moves...

It does counter steer when I tilt up/down (ELE)

I can steer the Swash all around with the TX stick.

I have tried to run it with 100% gain (can see the gain for ELE and AIL in the CGU display shows 100% AVCS....

Wonder if the unit is not working correctly

ChopperKnud
Team Miniature Aircraft
ThePitchbrothers

07-02-2016 11:12 PM
PM  EMAIL  GALLERY  Attn:RR
qroadrunner96

Heliman

Birmingham, AL

My Posts: All  Forum  Topic

Cgy 750

I would reset the unit and start over and if things dont work right send it back again

07-02-2016 11:58 PM
PM  EMAIL  GALLERY  Attn:RR
Knud Pedersen

Key Veteran

Denmark - Europe

My Posts: All  Forum  Topic

I've reset all menus and even updated it again.
Still the same.

Tried it with other model in the TX and vs.
Still the same.
So I guess it's not working correctly....will contact the service center - again

ChopperKnud
Team Miniature Aircraft
ThePitchbrothers

07-03-2016 12:59 PM
PM  EMAIL  GALLERY  Attn:RR
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

Slow down a sec.......which firmware?

Ben Minor

Team Synergy Team Futaba Team Kontronik USA
Progressive RC

07-03-2016 02:40 PM
PM  EMAIL  GALLERY  Attn:RR
Knud Pedersen

Key Veteran

Denmark - Europe

My Posts: All  Forum  Topic

I updated this CGY to software version v2 after i got it back from Ripmax and installed it in a furion 450. ...

This CGY was originally in my Fury 55 and I craahed the heli because it was uncontroable. Think it was with sw 1.3 or 1.4.

Bug a second hand CGY for my Fury55 and updated it ti v2 No issue.

I do have a short video showing the issue. Will opload it to YT tomorrow.

ChopperKnud
Team Miniature Aircraft
ThePitchbrothers

07-05-2016 10:17 PM
PM  EMAIL  GALLERY  Attn:RR
kcordell

Elite Veteran

O Fallon, MO

My Posts: All  Forum  Topic

Right Function for AIL Gyro in function menu?

Team Futaba, Team Synergy/Rail, Team Scorpion, Team Castle Creations, YS Engines, VelTye

07-07-2016 12:52 AM
PM  EMAIL  GALLERY  Attn:RR
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

If he's using 3D mode in 2.0, there is no sep Ail gyro gain. Both axes are under one channel as head gain.

Ben Minor

Team Synergy Team Futaba Team Kontronik USA
Progressive RC

07-07-2016 01:46 AM
PM  EMAIL  GALLERY  Attn:RR
Knud Pedersen

Key Veteran

Denmark - Europe

My Posts: All  Forum  Topic

I do use 3d mode.
RIPMAX jusr comfirm that the unit had a.mal function.
Bought a replacement unit.

ChopperKnud
Team Miniature Aircraft
ThePitchbrothers

07-09-2016 10:22 AM
PM  EMAIL  GALLERY  Attn:RR
WATCH  1 page 390 views POST REPLY
ProModeler Scorpion Power
 Print TOPIC Advertisers 

 4  Topic Subscribe

Sunday, December 4 - 8:22 pm - Copyright © 2000-2016 RunRyder   EMAILEnable Cookies