RunRyder RC
 4  Topic Subscribe
WATCH  2 pages [ <<    <     1     ( 2 )    >    >> ] 905 views POST REPLY
ProModeler Scorpion Power
plakkertje

Senior Heliman

belgium

My Posts: All  Forum  Topic

Muth bether with gov gain at 9
next is the servo horn...

07-11-2016 05:06 AM
PM  EMAIL  Attn:RR
buburub

Senior Heliman

Bayside, NY

My Posts: All  Forum  Topic

Great news!! Keep us posted!!

Goblin 700 KSE, Goblin 700 Comp, Align 700L Dominator, Align 700N, Logo 550SX

07-11-2016 09:35 AM
PM  EMAIL  GALLERY  Attn:RR
plakkertje

Senior Heliman

belgium

My Posts: All  Forum  Topic

Okay,
on the middle hole in the servo horn and the gov gain at 9 and it is bether but need that little bit more holding on the pumps...
next thime i will play an little more with precomp.
i have the 24t pul on but have the feeling that more rpm would be bether...
But i have 1900rpm on my main and i have the feeling that my lipo's
have to work very hard and the engine is already realy hot.
now i have an 490kv engine with an 22t motor minion,
if i go higher with the kv on an engine and an smaller pulley, what will it to the lipo's engine temp,...?
thx

07-17-2016 07:55 PM
PM  EMAIL  Attn:RR
buburub

Senior Heliman

Bayside, NY

My Posts: All  Forum  Topic

I'm running a scorpion 4530 540kv motor with stock pinion. I'm also running the sab 115 tail blades. Do the following. 1) make sure the tail is mechanically trimmed. Hover about 30 feet in the air and click the switch so the tail goes to rate mode instead of heading hold mode. If the tail rotates then it is not mechanically trimmed. Adjust the tail push rod length until the tail does not rotate in rate mode. 2) readjust tail end points 3) fly fast backwards like full speed hurricane or full speed backwards loop. Adjust the tail gain so it wags at high speed and then back it down a click so it does not anymore. 4) lastly you adjust the tail precomp until tail does not kick out. If after all this the tail still kicks out then you need to consider your tail servo might be too weak or at the very least suspect. Also make sure your tail assembly is not binding
Bub

Goblin 700 KSE, Goblin 700 Comp, Align 700L Dominator, Align 700N, Logo 550SX

07-17-2016 08:06 PM
PM  EMAIL  GALLERY  Attn:RR
plakkertje

Senior Heliman

belgium

My Posts: All  Forum  Topic

Thx i wil try that!!

07-17-2016 08:15 PM
PM  EMAIL  Attn:RR
plakkertje

Senior Heliman

belgium

My Posts: All  Forum  Topic

What are your headspeeds Bub?

07-17-2016 08:17 PM
PM  EMAIL  Attn:RR
buburub

Senior Heliman

Bayside, NY

My Posts: All  Forum  Topic

1900 head speed, motor temp after hard 3d around 145 to 155 degrees, esc temp 120 to 125 degrees. Battery temp 110 to 115 degrees. I believe the 24th tail pulley is the high speed tail setup

Goblin 700 KSE, Goblin 700 Comp, Align 700L Dominator, Align 700N, Logo 550SX

07-17-2016 08:42 PM
PM  EMAIL  GALLERY  Attn:RR
plakkertje

Senior Heliman

belgium

My Posts: All  Forum  Topic

Deg celcius??

07-17-2016 09:53 PM
PM  EMAIL  Attn:RR
buburub

Senior Heliman

Bayside, NY

My Posts: All  Forum  Topic

Farenheight

Goblin 700 KSE, Goblin 700 Comp, Align 700L Dominator, Align 700N, Logo 550SX

07-17-2016 09:57 PM
PM  EMAIL  GALLERY  Attn:RR
plakkertje

Senior Heliman

belgium

My Posts: All  Forum  Topic

Realy?
what engine and esc are you using?

07-18-2016 09:26 PM
PM  EMAIL  Attn:RR
plakkertje

Senior Heliman

belgium

My Posts: All  Forum  Topic

Are there somone ho have the cgy on the kse 700?
please chare jour tail setup, what servo, what hole on the servo horn, gain,rpm,etz,...
mine is not holding perfektly with tik toks and sudden pitch pumps.
Thx

08-24-2016 05:01 AM
PM  EMAIL  Attn:RR
WATCH  2 pages [ <<    <     1     ( 2 )    >    >> ] 905 views POST REPLY
AlignRC Thunder Power RC
 Print TOPIC Advertisers 

 4  Topic Subscribe

Thursday, December 8 - 6:08 pm - Copyright © 2000-2016 RunRyder   EMAILEnable Cookies