Topic Subscribe
WATCH  1 page487 viewsPOST REPLY
HeliDirect . Heli-Max . Scorpion Power System
. .

e-
Align T-REX 100 150 250 450 500 550 600 700 800
 >

T-REX 450
new trex 450 dfc problem
wc_wickedclown

Elite Veteran

long beach calif

do i use h-1 or h3 for swash type for sbus
3gx mr gyro

Team Tarot usa associate pilot ^_^

10-08-2013 05:39 AM
HOMEPAGE  
Dino Spadaccini

Elite Veteran

USA

h3 with the 3gx
put 3gx in to dir mode to due setup your best bet is to install the software and follow the install setup


Dino

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-08-2013 03:01 PM
wc_wickedclown

Elite Veteran

long beach calif

Dino Spadaccini
h3 with the 3gx
put 3gx in to dir mode to due setup your best bet is to install the software and follow the install setup
its the new 3gx mr it uses h1 since it is sbus

Team Tarot usa associate pilot ^_^

10-08-2013 04:29 PM
HOMEPAGE  
Dino Spadaccini

Elite Veteran

USA

how are you justing the travel on the ALR ELE and Pitch H1

please explain if you are using end points you are incorrect in the setup Sbus allow the servos to plug into the 3gx and one wire to the rx into the sbus port instead of using the wire to wire setup. you must power the 3gx first not the rx

Dino

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-08-2013 04:45 PM
wc_wickedclown

Elite Veteran

long beach calif

Dino Spadaccini
how are you justing the travel on the ALR ELE and Pitch H1
please explain if you are using end points you are incorrect in the setup Sbus allow the servos to plug into the 3gx and one wire to the rx into the sbus port instead of using the wire to wire setup. you must power the 3gx first not the rx
Dino
the 3gx mr


the rx is built in the servos plug directly into the gyro

im trying to figure out how to adjust the travel on the elevator servo now because when i move the throttle up and down the elevator servo goes up then mid then low but when i push the elevator stick forward the servo goes up but when i pull the elevator stick back in only goes down to mid i can't get full throw down

Team Tarot usa associate pilot ^_^

10-08-2013 05:04 PM
HOMEPAGE  
Dino Spadaccini

Elite Veteran

USA

you need to use a RX with Sbus that is only for spk SIR

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-08-2013 05:13 PM
Dino Spadaccini

Elite Veteran

USA

1. For Futaba S.BUS receivers, connect wires as shown in diagram.

2. While using the speed controller that not including BEC, you need to connect the BEC power with 3GX "BATT" port.

3. Receiver power is supplied through S.BUS signal wire connected to 3GXs S.BUS/BIND port.

Caution:The battery must be directly connected to the input of 3GX to ensure the adequate power of the servo. Please supply the receiver via 3GX Batt out.

4. The default channel/function mapping when using S.BUS are:

(1)AIL (2)ELE (3)THR

(4)RUD (5)GAIN (6)PIT

(7)GOV

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-08-2013 05:23 PM
Dino Spadaccini

Elite Veteran

USA

that info is from inside the 3gx software Dino

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-08-2013 05:24 PM
wc_wickedclown

Elite Veteran

long beach calif

Dino Spadaccini
that info is from inside the 3gx software Dino
the 3gx mr does not have rx the rx is built into the gyro

the 3gx mr does not have a usb port to program or tweak the gyro
everything is done manually.

thank you thank you for your time and advice brother.


this video is a bit long but you can see my issue bear the middle close to the end

Watch at YouTube

Team Tarot usa associate pilot ^_^

10-09-2013 12:52 AM
HOMEPAGE  
Dino Spadaccini

Elite Veteran

USA

ok your using a bind and fly you should have said that i will post a vid that shows the setup sorry for the mistake on which 3gx you are using


Dino

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-09-2013 02:03 PM
Dino Spadaccini

Elite Veteran

USA

Watch at YouTube

3gx MRS

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-09-2013 02:05 PM
wc_wickedclown

Elite Veteran

long beach calif

Dino Spadaccini
ok your using a bind and fly you should have said that i will post a vid that shows the setup sorry for the mistake on which 3gx you are using
lol i didn't know what i had guy brought i over for me to fix
he is a new pilot he bought it on ebay but when he came over
he had now box and i didn't know about the new RTF sport and
i didn't know the mrs came in a black case too

Team Tarot usa associate pilot ^_^

10-09-2013 02:31 PM
HOMEPAGE  
Dino Spadaccini

Elite Veteran

USA

so you are good now


Dino

RIP Roman JR
Capt USA Align Factory Team Align - Conquer Your heart
Team Futaba

10-09-2013 02:34 PM
wc_wickedclown

Elite Veteran

long beach calif

Dino Spadaccini

Watch at YouTube

i did not use his normal pitch curves 75%@ mid stick i don't have
the balls to try i know better and he is using linear curves for 3d

still a excellent vid thanks
i did all that but the radio has no backward elevator control
i think the radio is broken.

i am scheduled to go to the align usa to meet with them to look at this bird.

thank you for all your help

Team Tarot usa associate pilot ^_^

10-09-2013 02:44 PM
HOMEPAGE  
WATCH  1 page487 viewsPOST REPLY
Ron's RC Helicopters . Thunder Power RC . Mikado
. .

e-
Align T-REX 100 150 250 450 500 550 600 700 800
 >

T-REX 450
new trex 450 dfc problem
 Print TOPIC Advertisers 

Topic Subscribe

Monday, July 28 - 1:20 pm - Copyright © 2000 - 2014 runryder.com | email | runryder needs cookie