RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 725 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
2 pages [ <<    <     1     ( 2 )    >    >> ]813 viewsPOST REPLY
CarbonXtreme . Midland Helicopters . HeliProz

.
.
e-Mikado Logo 400 500 600 > It Begins!!!!
 
 
Riq
Senior Heliman
Location: ND

My Posts This: Topic  Forum

I use 4200s.
11-16-2009 07:08 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
OICU812
rrProfessor
Location: Grande Prairie, Alberta, Canada

My Posts This: Topic  Forum		Did u run a slave port wire from jive bec? Observe polarity markings on case that parralels output power. Should be able to almost stall servos with no brownout and u should also select 6volts output to as well for buffer voltage

...Once upon a time there were Nitros, flybars and frequency pins...
11-16-2009 08:27 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
MTBSuspEng
Heliman
Location: Madison, Wi

My Posts This: Topic  Forum		Currently running both the slave and master to the RX, I'm going to try running the slave directly to the Vbar. I'll recheck all my wiring this evening. Also I hear my problem could be due to the close proximity of the TX and RX indoors, so I'll take it outside this evening and see if anything changes. If problems continue I'll pick up a Spektrum flight log from the LHS.
11-16-2009 08:32 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
OICU812
rrProfessor
Location: Grande Prairie, Alberta, Canada

My Posts This: Topic  Forum		Ya u should def have tx and RC a few feet apart and check slave wire polarity on bec output it's easy to get wrong aak me how I know lol

...Once upon a time there were Nitros, flybars and frequency pins...
11-16-2009 09:21 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
Big Fil
Veteran
Location: Santa Rosa

My Posts This: Topic  Forum
Quote 
How heavy did it end up, any idea ?
The 10s hyperion g3vx 4200 are 1140g and the 3300 are 930g. Out of these two, which one would u guys use on a similar logo ?

My setup is almost exactly what MTBSuspEng's is and mine comes in at 7.98lbs AUW. Only difference is MTB is using far more velcro straps.

You'll want to run the 4200s for a Logo 600. I'm running the G3Vx packs and they CG well.

Mikado
Edge Blades
11-16-2009 09:47 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
2 pages [ <<    <     1     ( 2 )    >    >> ]813 viewsPOST REPLY
Ron’s HeliProz South . MTA Hobbies . Model Rectifier Corp

.
.
e-Mikado Logo 400 500 600 > It Begins!!!!
 
 
HeliMan Dave
Senior Heliman
Location: Chicago

My Posts This: Topic  Forum		MTB, Looks good but a few things I'd like to point out.

#1, Be careful if you really leave the tail servo wire tucked inside the frame where the boom gets clamped. I would be nervous that the servo leads would get pinched when you sandwich the frames together and tighten the screws.

#2, I'd put the ground wire screw in the bottom of the boom instead of the side. On the inside of the boom, the belt will run very close to the screw and could get shredded.

#3 I'd find a different place to mount the satellite RX instead of directly on the side of the cyclic servo. Servos are very RF noisy and may cause unintended interference. I'd suggest the side of the main frame.

Logo 500 3D / E550 Raptor / E325 mini-Titan / T-Rex 250 / Blade CX-2 / Blade mCX
11-17-2009 04:46 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
2 pages [ <<    <     1     ( 2 )    >    >> ]813 viewsPOST REPLY
CarbonXtreme . Midland Helicopters . HeliProz

.
.
e-Mikado Logo 400 500 600 > It Begins!!!!
 Print TOPIC Advertisers 

Subscribe to This Topic

Monday, November 23 - 2:40 pm - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF