RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 900 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
1 page288 viewsPOST REPLY
HeliProz . Ron’s HeliProz South . MTA Hobbies

.
.
Avant Aurora - EFX - FX > AURORA ROD LENGHTS
 
 
RACER7696
Heliman
Location: Ma

My Posts This: Topic  Forum		Guys, Does any one know what the lenghts are from cener of ball link to center of ball link are supposed to be. I am assembling a usued machine and the links were off, When I look at the manual it just says 4 rods at 85 mm and so on . Does that mean I shoild just screw the ball links on each end and when I have 85 mm of rod between them I am done. Please forgive such a stoupid question as the anwser is proberbly right in front of my face. Or maybe its the 10 hours ive spent today trying to get this thing ready to fly.


Thanks,Mark
10-25-2009 02:36 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
Dood
Elite Veteran
Location: WI

My Posts This: Topic  Forum		These should get you in the ball park if you're using ACTIVE head setting.
These measurements are CENTER TO CENTER of the ball links.

There are lengths printed in the Aurora manual as well



Don't forget this link should make a 90° angle to the mixing arm at 0° pitch.



3 years is enough time wasted. Taking a break for a while.
10-25-2009 02:42 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
RACER7696
Heliman
Location: Ma

My Posts This: Topic  Forum		So you measure the rod between the begining of the ball link and the rod.Why dont they just give a measurement from center of ball link to center of ball link, Like most manufactures. Also that way you can use a ball link set up tool to make things enen easier. Could you also tell me where in the manual the rod lenght are. The one I found is on the last two pages and it just says 4- 80mm threaded rod. av00-200-523 short carbon pushrod,av00-200-996 100mm threaded rod av00-200-995 2 85mm rods, av00-200-991-3 35mm rods , av00-200-997 2 135mm threaded rods, So again are they telling me that this is what should be showing between the rod lenghts, Because these measurements dont work for center of ball link to center of ball link.So if possible could you give me a little more explenation.

Thanks for everyones time
Mark
10-25-2009 04:44 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
1 page288 viewsPOST REPLY
Model Rectifier Corp . ReadyHeli . Power Helis

.
.
Avant Aurora - EFX - FX > AURORA ROD LENGHTS
 
 
Jason Bell
Elite Veteran
Location: San Diego, Ca

My Posts This: Topic  Forum		If you look at the parts listing on the avant rc site, you can see all the linkage rod lenghts at the bottom of the list. Here

The manual gives general linkage rod lengths between the ends of the ball links, which is another way to measure the lengths of the rod. It works just as well as measuring center to center.

Another way I come up with the servo linkage rod lengths are by placing the ball link in the servo screw, so the hole in the link fits in the servo screw, and adjust the linkage rod length to the center of the CCPM control shaft, this gets me about 99% close to the desired linkage rod length.

Team Avant
Aerospire
Radix
Solid G
Canopy Works
Thunder Power RC
Spektrum RC
10-25-2009 05:03 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
1 page288 viewsPOST REPLY
HeliProz . Ron’s HeliProz South . MTA Hobbies

.
.
Avant Aurora - EFX - FX > AURORA ROD LENGHTS
 Print TOPIC Advertisers 

Subscribe to This Topic

Tuesday, November 24 - 3:44 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF