RunRyder RC Helicopter Topic - Outrage FBL Head

RR Rated M For Mature

HOME rrTV-PHOTO GALLERIES MY GALLERY HELP-FAQ

myHOME PM pmRR MEMBERS 410 ONLINE 18 EVENTS SEARCH REGISTER START HERE

1 page

348 views

POST REPLY

Autography FlightPower	.	Advantage Hobby	.	Revolution Models
	.		.

Flybarless Rotor Head Systems > Outrage FBL Head

kineticheli
Heliman
Location: Turlock, CA

My Posts This: Topic Forum

I was helping a flying buddy put together his Outrage head over the weekend and noticed that there were three hole to put the ball onto the pitch arm. My question is what difference does it make? It is a T-Rex 600e with 9252 servos. I put them in the middle hole for now. He is waiting on a SK360 to fly.

Raptor 50, Hyper 50, GY401, 600D
Kinetic, Hyper 50, GY401, Radix

10-20-2009 03:49 PM

PROFILE PM EMAIL POSTS BUDDY IGNORE GALLERY

Jag72
Elite Veteran
Location: 20 minutes south of Boston Mass...

My Posts This: Topic Forum

Holes...

The holes are so you can adjust the resolution....

depending on the ratio of the setup you can use whatever hole gives you the best flight characteristics....

I usually just use the middle hole ...set servos at 10-11mm from center on servo arms for that machine ...and I put shorter balls on the center of the swash...going from swash to pitch arms..

But I suppose if you use the stock length inner swash balls you may want to consider using the outermost holes on the arms...

Esprit Model Flight Team

10-20-2009 04:39 PM

PROFILE PM EMAIL POSTS BUDDY IGNORE GALLERY

kineticheli
Heliman
Location: Turlock, CA

My Posts This: Topic Forum

Thanks for the reply. I'll leave it alone till we fly this weekend.

Raptor 50, Hyper 50, GY401, 600D
Kinetic, Hyper 50, GY401, Radix

10-20-2009 08:25 PM

PROFILE PM EMAIL POSTS BUDDY IGNORE GALLERY

theflyingman2
Senior Heliman
Location: Winter Haven, FL USA

My Posts This: Topic Forum

I aggree with Jag, the holes are for different resolution. The further out the ball is on the grip the higher gain you will be able to run. Same idea as tail gyro setup. Im running all stock lengths, with the balls in the outer holes on the grip arms. Works like a charm.

I find the harder I "throw down" at the field... the more peices i have to pick up.

10-23-2009 02:30 AM

PROFILE PM EMAIL POSTS BUDDY IGNORE GALLERY

ajo1
New Heliman
Location: Anglesey

My Posts This: Topic Forum

Hi, I have just fitted this head on my Trex600 and have noticed that using the centre hole the blades will be 15mm lower down than the standard Align head, it there a potential problem with the baldes hitting the boom?.Andy.

11-04-2009 05:10 PM

PROFILE PM EMAIL POSTS BUDDY IGNORE

Jag72
Elite Veteran
Location: 20 minutes south of Boston Mass...

My Posts This: Topic Forum

No---

you can easily go a full inch lower with no problems

Esprit Model Flight Team

11-04-2009 05:36 PM

PROFILE PM EMAIL POSTS BUDDY IGNORE GALLERY

ajo1
New Heliman
Location: Anglesey

My Posts This: Topic Forum

Thanks for the reply Jag, dose this include full 3d flying.
Andy.

11-04-2009 05:45 PM

PROFILE PM EMAIL POSTS BUDDY IGNORE

1 page

348 views

POST REPLY

CarbonXtreme	.	Midland Helicopters	.	HeliProz
	.		.

Flybarless Rotor Head Systems > Outrage FBL Head

Jag72
Elite Veteran
Location: 20 minutes south of Boston Mass...

My Posts This: Topic Forum

YES....

I had mine lowered over 1" and fly fairly hard 3d.

never had any issues...if you look around you'll see some guys have lowered their heads SUPER low..(guessing almost 2"

and still had no issues...

I think 1" is more than safe though...

at least it was for me

Esprit Model Flight Team

11-04-2009 05:56 PM

PROFILE PM EMAIL POSTS BUDDY IGNORE GALLERY

1 page

348 views

POST REPLY

Autography FlightPower	.	Advantage Hobby	.	Revolution Models
	.		.

Flybarless Rotor Head Systems > Outrage FBL Head

Print TOPIC

Advertisers

Subscribe to This Topic