RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 508 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
6 pages [ <<    <     4      5     ( 6 )    >    >> ]1191 viewsPOST REPLY
CANOMOD . Experience RC . Heli-Max

.
.
e-E-Flite Blade MSR CP CX MCX 400-3D > Blade CP+ Pro Medusa out of business?? What about our tail motors???
 
 
Mitchilito
Senior Heliman
Location: Morehead City, NC USA

My Posts This: Topic  Forum

Bob, I can't honestly say which servo horn I used. Maybe this picture will help??

What are you going to install them in? You'll love them, I know.

Remember, if you install them in a CP you'll probably want to notch the frame for the wires.




perfection is the death of creation
11-22-2009 12:29 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
BOB WHO?
Veteran
Location: downey, ca., usa

My Posts This: Topic  Forum		I'm kinda focusing on a Trex 500 right now and might wait until I get this one up and running before I install the servos, but they are going on the razorblade. So you have to notch the frame? I'll figure it out probably.
11-22-2009 06:02 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Mitchilito
Senior Heliman
Location: Morehead City, NC USA

My Posts This: Topic  Forum		The wires come out of the DS450s on the bottom (when installed) vice the top on the junk stockers. I don't think it's an issue on the front servo but the two rears need to be notched.

perfection is the death of creation
11-22-2009 10:07 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
itsjojo
Veteran
Location: North East Pennnsylvania

My Posts This: Topic  Forum		Hi,
just checkin in again. I wrote Inethobby and they never sent out that 5300kv motor. As soon as I got the reply telling me this I got confirmation that it was just shipped. Go figure.

Still been busy with work as I write this. 5 hours of book work today Sunday! Yuck. I think by tomorrow morning I should be caught up.

chat soon!
jojo

Trex 500esp 600N Pro & 700 Nitro Dx7
11-23-2009 01:02 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
6 pages [ <<    <     4      5     ( 6 )    >    >> ]1191 viewsPOST REPLY
Hobby Hut . Heli Wholesaler . JR-Spektrum

.
.
e-E-Flite Blade MSR CP CX MCX 400-3D > Blade CP+ Pro Medusa out of business?? What about our tail motors???
 
 
zguy
Heliman
Location: SoCal

My Posts This: Topic  Forum		Had time to switch the TB9 out of my foamy today and checked the settings. It's on ver. 1.03 and does have 3 brake settings (off/soft/hard). I did find where Manuel wrote he uses the soft setting. I used hard brake to try and improve the stops and avoid the prop being spun backwards. Any one else with brake on/off experience?

It's tempting to remove the 401 case to save weight, but I'm too concerned about damage. It's the single most expensive component.

It'll be a week or so before the Hyperion 4000 and 401 come in. Curious on hard 3D flight performance of the Hyperion vs. the Medusa?
11-23-2009 01:14 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
6 pages [ <<    <     4      5     ( 6 )    >    >> ]1191 viewsPOST REPLY
CANOMOD . Experience RC . Heli-Max

.
.
e-E-Flite Blade MSR CP CX MCX 400-3D > Blade CP+ Pro Medusa out of business?? What about our tail motors???
 Print TOPIC Advertisers 

Subscribe to This Topic

Monday, November 23 - 6:26 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF