RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 881 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
1 page429 viewsPOST REPLY
Thunder Power RC . Mikado Modellhubschrauber . Futaba-RC

.
.
e-MSH Protos 500 > JR DS3517 - Protos + Servo Horns 16mm
 
 
fuhlemann
Senior Heliman
Location: Jackson, MI

My Posts This: Topic  Forum		Hey there,

I finally made it to get another Protos after my last one ended up being totalled due to a bec shutdown.

Now I wanted to go with the DS3517, not really the perfect fit, but after some trimming of the supports for the braces, it's all great and they fit just the way they are supposed to.

Now the manual recommends to go with 16mm servo horns, but they don't come with horns that size. Now I have tried to find these horns, but didn't really get lucky. Where can I find 16mm servo arms for JR servos? and then again, I need one for the tailservo (DS3500G) which needs 13.5mm according to the manual.

Thanks in advance
Florian

MSH Protos 6S
Next-D Rave 450 4S
Spektrum DX7 SE w/AR7600
09-16-2009 03:03 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
sbmon
Senior Heliman
Location: DEEP IN THE BOG

My Posts This: Topic  Forum		what length horns do the servos come with. If its off by 1 to 2 mm it's not really that big of a deal just play with the swash values to get the performance qualities you are looking for.
09-16-2009 03:46 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
drdot
Elite Veteran
Location: So. California, Orange County.

My Posts This: Topic  Forum		fwiw..

DuBro makes heavy duty servo arms for JR...The are just right...


John.
09-16-2009 03:58 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
kdii02
Heliman
Location: PA USA

My Posts This: Topic  Forum		Running mine with the stock 3517 arms. Yea they are off by a couple mm but I think it will be ok.

Kasama Srimok 90, MSH Protos 500, T-Rex 500 AIRWOLF, T-Rex 600ESP, T-Rex 250, Blade MSR
09-17-2009 07:34 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
sbmon
Senior Heliman
Location: DEEP IN THE BOG

My Posts This: Topic  Forum		I just installed the 3517mg servos in a cf protos and used the servo arms from JR 8717 servos. They fit perfectly and give a little offset to help the ail and aux servos clear the frames perfectly. Also if you used the rubber pads and brass inserts there is no need to trim the servo mounts to fit the 3517 servos.

shawn
09-17-2009 09:10 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
kdii02
Heliman
Location: PA USA

My Posts This: Topic  Forum		Great tip Shawn! I have some extra 8717 arms laying around. I think I'll try that!!

Kasama Srimok 90, MSH Protos 500, T-Rex 500 AIRWOLF, T-Rex 600ESP, T-Rex 250, Blade MSR
09-22-2009 02:56 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
fuhlemann
Senior Heliman
Location: Jackson, MI

My Posts This: Topic  Forum		i ordered the dubro 674 as they are the only ones that i could find with 16mm and i got a 12mm and 13mm for the tail, so i can try to get the best one for my new g370 gyro.

MSH Protos 6S
Next-D Rave 450 4S
Spektrum DX7 SE w/AR7600
09-22-2009 04:45 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
Flying Dutchy
Heliman
Location: The Netherlands

My Posts This: Topic  Forum		:D

Good to have you back in the Protos area Florian!
09-24-2009 12:36 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
fuhlemann
Senior Heliman
Location: Jackson, MI

My Posts This: Topic  Forum		Oh yes, it was such a blast to put the new kit together.. :-)

MSH Protos 6S
Next-D Rave 450 4S
Spektrum DX7 SE w/AR7600
09-24-2009 12:39 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
kdii02
Heliman
Location: PA USA

My Posts This: Topic  Forum		Ok you guys win.. I tried on the 8717 arms on my 3517's and they worked perfect. I had originally thought the stock 3517 arms were ok, but I noticed on the bench that they were indeed rubbing against the frame when I moved the sticks. So I replaced them and the heli is flying great now. Also moved the tail servo ball in to about 8.5 mm and the tail is holding solid now with the 370/3500g

Kasama Srimok 90, MSH Protos 500, T-Rex 500 AIRWOLF, T-Rex 600ESP, T-Rex 250, Blade MSR
09-28-2009 02:59 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
sbmon
Senior Heliman
Location: DEEP IN THE BOG

My Posts This: Topic  Forum		8.5 mm out on the 3500 tail servo is way too far in. Yes it will work but it is not ideal. I too am using a JR 3500 tail servo but with a spartan gyro. I have found that 13 mm is about ideal for protos tail geometry. This distance should give the best performance with good speed and resolution.
shawn
09-29-2009 01:02 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Sillyness
Veteran
Location: Little Rock AR

My Posts This: Topic  Forum		Does the 3500G use the same servo arms as the full size servos or do they have a smaller output shaft?

Thanks
10-13-2009 03:26 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
1 page429 viewsPOST REPLY
Boca Bearings . XHELI.COM . Autography FlightPower

.
.
e-MSH Protos 500 > JR DS3517 - Protos + Servo Horns 16mm
 
 
fuhlemann
Senior Heliman
Location: Jackson, MI

My Posts This: Topic  Forum		seems to be standard jr

MSH Protos 6S
Next-D Rave 450 4S
Spektrum DX7 SE w/AR7600
10-13-2009 04:19 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
1 page429 viewsPOST REPLY
Thunder Power RC . Mikado Modellhubschrauber . Futaba-RC

.
.
e-MSH Protos 500 > JR DS3517 - Protos + Servo Horns 16mm
 Print TOPIC Advertisers 

Subscribe to This Topic

Monday, November 23 - 1:00 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF