RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 865 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
1 page261 viewsPOST REPLY
Hobby Hut . Heli Wholesaler . JR-Spektrum

.
.
Synergy R/C Synergy N9 > tail slider question!!!!!!!!!!!!!!!
 
 
nikpepa
Heliman
Location: patras greece

My Posts This: Topic  Forum		i want to change the n9 tail slider and i dont want to put the some one but some better.what i have to buy to do that??please if someone can send me a link so to order all the stuff i need!


thankssssssss
08-19-2009 10:13 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Entityofme1
Senior Heliman
Location: Birmingham, AL.

My Posts This: Topic  Forum		The stock tail slider works just fine with a little bit of extra TLC ( tender, love, care). If you are scared of the way it all locks together with the star ring because of failures reported here on runryder I'll briefly explain what I do to make it more secure. I press the star ring on by hand carefully and evenly to where there is no back and forth end play/wobble and so the bearings are not notchy. I then take a razor knife and put a groove around the edges of the teeth on the brass slider. Lastly I mix up a little bit of 30 minute epoxy and then carefully fill in all around the end of the brass slider into the crevices of the star ring where it attaches. Some people do this with JB weld also and it will work as well. Let the epoxy cure properly for a good 24 hours and it should have excellent holding power.
08-19-2009 02:41 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
bkervaski
Key Veteran
Location: Birmingham, AL, USA

My Posts This: Topic  Forum		There's also the c-clip mod by Jim, he slots your brass slider then gives you a couple c-clips and shims, I use this mod and it works great.
08-19-2009 03:36 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
nikpepa
Heliman
Location: patras greece

My Posts This: Topic  Forum		where can i find c-clip by jim???

thanks
08-20-2009 08:56 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
bkervaski
Key Veteran
Location: Birmingham, AL, USA

My Posts This: Topic  Forum		PM sent.
08-20-2009 05:12 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
Aleheli
Heliman
Location: Brazil and USA

My Posts This: Topic  Forum		Please send me a PM too
Regards
Alex
09-09-2009 12:29 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
1 page261 viewsPOST REPLY
E-flite . Fast Lad Performance . Ace Hobby

.
.
Synergy R/C Synergy N9 > tail slider question!!!!!!!!!!!!!!!
 
 
RotorHead486
Key Veteran
Location: England

My Posts This: Topic  Forum		Hey,

I just use a better quality star locking washer which are available from most hardware suppliers.

On both my synergy's the star locking washer was not a very good fit on the brass bushing, i've since replaced with the starlock washer below which is a much better fit on the bushing and it takes quite a bit of force to punch it onto the bushing and you can see it dig into the brass, so this washer is doing what it's supposed to do.

You can get them from most Engineering suppliers, i got some 8mm ID starlock washers and they were spot on.



Cheers!
Rossco

One Reason For Crashing'Rogue Servo Bent on World Domination'!!
QuickUK Pilot
09-09-2009 01:05 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
1 page261 viewsPOST REPLY
Hobby Hut . Heli Wholesaler . JR-Spektrum

.
.
Synergy R/C Synergy N9 > tail slider question!!!!!!!!!!!!!!!
 Print TOPIC Advertisers 

Subscribe to This Topic

Tuesday, November 24 - 12:23 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF