RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 842 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
1 page224 viewsPOST REPLY
Esprit Model . Thunder Power RC . Mikado Modellhubschrauber

.
.
Blitz Helicopters Avro 90 > Torque tube bearing supports
 
 
pgrbff
Veteran
Location: Louth, Ireland

My Posts This: Topic  Forum		When you "bend" the torque tube in a crash, do you get to re-use the bearing supports?

Proficient at turning cash and credit into smoke and noise!
08-15-2009 01:04 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
stanc
Key Veteran
Location: Conroe, TX

My Posts This: Topic  Forum		If they aren't broken, I don't see why not. Bearing also if you can get them off and they aren't notichy.

Stan
Logo 500
Ion X2
eStratus
eAvro90
08-15-2009 01:21 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
pgrbff
Veteran
Location: Louth, Ireland

My Posts This: Topic  Forum		Instructions say to us medium C/A when placing them. I just wondered if medium loctite/bearing retainer was intended.

Proficient at turning cash and credit into smoke and noise!
08-15-2009 01:27 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
stanc
Key Veteran
Location: Conroe, TX

My Posts This: Topic  Forum		No, CA is what they meant to be used. I guess you could use Blue or Red Loctite, then to get the bearings off you can use a heat gun.

Stan
Logo 500
Ion X2
eStratus
eAvro90
08-15-2009 01:41 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
pgrbff
Veteran
Location: Louth, Ireland

My Posts This: Topic  Forum		Never seen "medium" C/A

Proficient at turning cash and credit into smoke and noise!
08-15-2009 01:44 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
stanc
Key Veteran
Location: Conroe, TX

My Posts This: Topic  Forum		It's a little thicker than the Instant, takes a little more time to dry.

Stan
Logo 500
Ion X2
eStratus
eAvro90
08-15-2009 01:50 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
pgrbff
Veteran
Location: Louth, Ireland

My Posts This: Topic  Forum		So viscosity, not strength.

Proficient at turning cash and credit into smoke and noise!
08-15-2009 01:52 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
stanc
Key Veteran
Location: Conroe, TX

My Posts This: Topic  Forum		That's right, strength is the same.

Stan
Logo 500
Ion X2
eStratus
eAvro90
08-15-2009 02:05 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
pgrbff
Veteran
Location: Louth, Ireland

My Posts This: Topic  Forum		Thanks

Proficient at turning cash and credit into smoke and noise!
08-15-2009 02:07 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
Climax
Veteran
Location: West London, United Kingdom

My Posts This: Topic  Forum		I used Epoxy on mine, it's so much easy to use than CA. You can simply wipe of any suplus, also you don't run the risk of having it wick into the bearings.
08-15-2009 06:19 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
pgrbff
Veteran
Location: Louth, Ireland

My Posts This: Topic  Forum		I found one of them was so tight I could barely slide it along the tube, only half of the bearing is over the C/A and its 4 or 5mm short of the mark, but I'm not going to try and get it off!

Proficient at turning cash and credit into smoke and noise!
08-15-2009 06:36 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
1 page224 viewsPOST REPLY
Futaba-RC . Boca Bearings . XHELI.COM

.
.
Blitz Helicopters Avro 90 > Torque tube bearing supports
 Print TOPIC Advertisers 

Subscribe to This Topic

Monday, November 23 - 5:13 pm - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF