RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 648 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
1 page296 viewsTOPIC CLOSED
Advantage Hobby . Revolution Models . CarbonXtreme

.
.
Thunder Tiger Raptors 30-90 - Imperio > RAPTOR 50 titan se build question
 
 
datidun
Senior Heliman
Location: n ireland

My Posts This: Topic  Forum		wonder if someone can give advice on the tail unit assembly on new titan se ,the question is how tight should the tail pitch control fork be on the slider and bushing ,i find if its sort of snug tight the bearing is to tight to turn ,i have added a bit of lock tight to bushing thread and loosened it up a bit its slightly tighter than hand tight and running smooth ,concerned its not tight enough ,thanx
07-02-2009 12:34 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
rexxigpilot
Key Veteran
Location: florida

My Posts This: Topic  Forum		You have it right. The bearing needs to turn freely! I turned it until the bearing was slightly restricted, then backed off 1/8 turn. The locktite and rotation of the shaft will keep it together.
07-02-2009 02:02 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
BarracudaHockey
rrMaster
Location: Orange Park FL

My Posts This: Topic  Forum		Make sure you give the locktite several hours to cure before flying it.


AMA 77227
http://www.jaxrc.com
07-02-2009 02:46 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
datidun
Senior Heliman
Location: n ireland

My Posts This: Topic  Forum		thanx for the replies guys i got it right ,i finished the building the kit today ,strange thing there is one part left over its a small bar almost the same as a feathering spindle or tail rotor shaft its very light aluminium type two small holes at the top and bottom ,i have been over the manual over and over ,its not even listed in the part section ,also to mention they give you the extra tail rod if you want to mount the rudder servo up front which is not mentioned in the manual ,thanx
07-02-2009 09:36 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
BarracudaHockey
rrMaster
Location: Orange Park FL

My Posts This: Topic  Forum		Better off using that tail rod to put the servo in the front.

I think that peice you're talking about, if its the same as the Titan (I havent had a good look at Tv2 yet) it goes on the very front of the servo tray and stabilizes the canopy from flopping back and forth.


AMA 77227
http://www.jaxrc.com
07-02-2009 11:28 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
datidun
Senior Heliman
Location: n ireland

My Posts This: Topic  Forum		ok they give you the tail pushrod for upfront ,but it doesnt fit the new type of pitch plate is in the way even if you take out the new pitch plate method and went with the old collective way it still cant fit ,because the way the elevator servo is put in its in the way and also open space were the rudder servo could go in is made the opposite way so no servo mounting screws can go in,so i had to put the rudder servo on the boom ,i also came across an issue with the throttle servo which goes slightly deeper into the frame causing the servo links and rod not to sit flush with the carb arm ,i will have to put a plate behind the servo to bring it out a bit
07-08-2009 08:14 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
1 page296 viewsTOPIC CLOSED
Midland Helicopters . HeliProz . Ron’s HeliProz South

.
.
Thunder Tiger Raptors 30-90 - Imperio > RAPTOR 50 titan se build question
 Print TOPIC Advertisers 

Subscribe to This Topic

Tuesday, November 24 - 5:19 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF