RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 682 ONLINE 80 EVENTS SEARCH REGISTER  START HERE
 
15 pages [ <<    <     1      2     ( 3 )     4      5     NEXT    >> ]8436 viewsPOST REPLY
EDGE Rotorblades . ReadyHeli . Power Helis

.
.
QuickWorldWide Ep and Wet Fuel Helis > Bat 26cc build pics.
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum

Okay , I realy did not like the tail pitch slider hitting the tail pitch lever mounting plate . So , I did some tinkering and came up with a fix for it. I fly the Quick of Japan EP8`s and EP9`s, and the tail set-up is pretty much the same design. I took a tail pitch lever mounting plate and pitch lever off an EP8 Expert which is a little bit shorter(the tail pitch lever mounting plate), so now the pitch slider clears the mounting plate and the geometry is correct for full deflection in both directions. ...
In the first picture is the Bat 26cc tail pitch lever mounting plate held up to the Quick of Japan EP8 EX tail pitch lever mounting plate to show the difference in length.



EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
smallplanes
Elite Veteran
Location: S.C. ,USA

My Posts This: Topic  Forum		That should work but want your servo have to move more to correct thetail with the shorter arm?
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		No , the geometry of the lever is different than the stock one



The ball links on the bottom of the links that go from the swashplate to the upper mixing arms are hitting the 3 x M2X4 Phillips Screws that hold the bearing in the swashplate .Anyone run into this problem ?



EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
Jon QWW
Heliman
Location: Coopersburg, PA 18036

My Posts This: Topic  Forum		Hey Jimbo,

We are using M2x4 flat head screws on the swashplates now. I must have missed that. I will drop a few in your box going out today. Just counter sink the holes in the swashplate and you will be good to go.
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		I had some stainless steel flat head screws to go in it. I always keep plenty of screw stock on hand. Thank you for the Quick reply!!

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Man , the guys at QWW have realy been good to me. Some of you other vendors need to have the same customer service as QWW. QWW has made a good customer out of me . they have my support . Great bunch of guys to deal with.. Thanks QWW.

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Can someone show me how and where they have thier electronic ignition
mounted ? I think this is one area I may need help in.
I fly DSM2 Spektrum so it realy should not matter where I mount it.

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-21-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Can somebody help me in hooking up my carb on my 26cc Bat v2 Gasser ?
How do I set up the tank, how many lines in the tank ? One vent line and one to the carb fuel intake? Thanks for the help, I`m new to gassers and I`m stumped on this one??? Thanks.

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-21-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
bates517
Heliman
Location: hanover

My Posts This: Topic  Forum		carb

if you have two nipples on carb one is a return line the other is a fuel in line you will have a vent line also. the vent line should be the one that is bent up to almost to the top of the tank inside. the fuel in should the one where the thumb primer is. the return is the one on the oppiset side of carb.

MASTER MATER
12-21-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		This carb only has one inlet for fuel



EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-22-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
JuanRodriguez
Elite Veteran
Location: Rochester, New York

My Posts This: Topic  Forum		Should be a "conventional" setup (no muffler pressure, though)...just like with your nitro motors..... Nipple on the carb to the fuel pick up on the tank and then the other line on the tank is your vent..... Some run a third "fill" line, but that is not mandatory....
12-22-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Thanks Juan...

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-22-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
smallplanes
Elite Veteran
Location: S.C. ,USA

My Posts This: Topic  Forum		Jim are you going to put a airfilter on your carb? I ordered one of the K&N cone type from QWW for mine.


Thanks
12-22-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Yup , I`m going to use a filter. I just have to wait until after X-mas to afford one...

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-22-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Okay guys, I need help with the canopy. How do you mount this thing ?
I am stumped on this one. How do you get it around the muffler; or does it go between the pipe and the frame ? Also , what hardware do you use ? I do not have any stand-offs in the hardware????



EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-23-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
smallplanes
Elite Veteran
Location: S.C. ,USA

My Posts This: Topic  Forum		I need to know the same thing. My kit does not have any mounting hardware ether,and the instrutions does not show how to mount it. I have a few parts missing from my kit.I'm going to call Irwin on the parts i need i know he will take care of it. I got a shipment from him today for a new fan(that i broke)i got the cnc blue alum fan. I also got my K&N airfilter and alum boom support. Jim is that your ignition mounted under the heli? I've been wondering where i was going to mount mine.


Thanks
12-24-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Yes that is the EI, it looked like a good a place as any..

EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-24-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
smallplanes
Elite Veteran
Location: S.C. ,USA

My Posts This: Topic  Forum		Looks good, i might mount mine there.
12-24-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
jimboflies
Elite Veteran
Location: Beaumont, Texas;

My Posts This: Topic  Forum		Okay , I just got my 680mm blades today!! Thank you Irwin!!!!!
These are realy nice blades; I like the airfoil on them and they are very stiff.Man , I realy can`t wait to fly this heli.
I am getting very close now . I can set up all of my pitch curves and throttle curves now . I got lucky when I set everything up by eye-ball. Full negative pitch is 15* degrees ; Full positive pitch is 15* degrees , and half stick is 0* degrees pitch. That is without any binding at all. AWSOME!!!!
I guess I will set the head up with 11* degrees pitch , positive and negative in Idle up 1 ; Normal around 11* positive and 3*degrees negative. Hold , 12* positive , 5* degrees negative....
Here are some pics of the blades. Realy some nice blades. Thank you again Irwin and Jon at QWW. You guys have realy helped me out tremendously. Awsome customer service from QWW.



EP8 EX twinring frame
Quick of Japan
EP8v2 EX
EP9
Quick World Wide Bat 26cc gasser
12-25-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
15 pages [ <<    <     1      2     ( 3 )     4      5     NEXT    >> ]8436 viewsPOST REPLY
CANOMOD . Experience RC . Heli-Max

.
.
QuickWorldWide Ep and Wet Fuel Helis > Bat 26cc build pics.
 Print TOPIC Advertisers 

Subscribe to This Topic

Saturday, March 20 - 2:44 pm - Copyright © 2000 - 2010 runryder.com | email | link to rr | START HERE | NF