RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 351 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
1 page1256 viewsPOST REPLY
Boca Bearings . XHELI.COM . Autography FlightPower

.
.
e-E-Flite Blade MSR CP CX MCX 400-3D > Blade 400 3D B400 swashplate problems after install HS65MG,need help.
 
 
elad400
Heliman
Location: israel

My Posts This: Topic  Forum		hello,

after installing hs65mg I made some adj in swashplate mix and servo rev,
the travel of one aileron servo when play with pitch is more then the other one ,I tried to switch between the servo cables in the reciver
but still one of the servos travel too far (up & done pitch),
so I think its somting with the transmitter programing, so I learned the
manual and not found a way to adj travel of only one of the aileron servos,
need help with that,
regards
Elad.
05-07-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
whirlydude
Senior Heliman
Location: USA

My Posts This: Topic  Forum		It sounds to me that your setup is off. Rather than trying to explain this it would be better to watch a video of how it is done. You need to go to www.helifreak.com. Go to Finless Bob's tech talk, and then to heli skills and setup 101. You will need to login in to watch the videos, but they are very well done and informative. Go to ccpm setup part 1 & part 2. These will show you how to setup your heli. Happy Flyin!
05-07-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
elad400
Heliman
Location: israel

My Posts This: Topic  Forum		It's OK now

Aux1=pitch servo not as same travel adj as the rest...
first time flying ccpm heli...


all the swashplate servos need to be at the same travel, pitch adj
only by link adj.
05-07-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
speeddemon370
Veteran
Location: Spruce Grove, Alberta, Canada

My Posts This: Topic  Forum		http://www.rchelimag.com/pages/howto.php?howto=6&page=3

This helped me out BIGTIME. I'd probably still be grounded without it.

with 2 ears and 1 mouth you should listen twice as much as you talk
05-07-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
zaw
Key Veteran
Location: Lebanon, NH - USA

My Posts This: Topic  Forum		Also Make sure that your swash is setup to 120*

Make sure you PIT is set to like 50% to start with. Disconnect all the linkages that are NOT connected to servos or you will bind and damage the servo during setup!. Go thought all the reversing procedures on CH 1,2 and 6. Juggle all the channels until you get it all right. it take time but you will get it.

After you get the swash plate move properly then reconnect the linkages. if they're Standard 90* servo's you should not need to adjust the travel at all. You can limit all at same time by changing pit percentage. If you limit the travel on swash servo you pit setting will be off and screw you up when you're setting up your pitch.

ಠ_ಠ HBK2 built with inexpensive parts! ٩๏̯͡๏)۶ Gaui425
05-08-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
StevenT
Veteran
Location: Dallas, GA USA

My Posts This: Topic  Forum		Was does PIT stand for? I'm going through the same problem with my 65's, but I think I've figured it out.

Steven

Shhh, don't tell the wife.
05-08-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
elad400
Heliman
Location: israel

My Posts This: Topic  Forum		Thank's

I adj the links after adj the swashplate ,big improvement
now the heli fly's excellent!
05-08-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Merlin1205
Heliman
Location: Winter haven FL

My Posts This: Topic  Forum		PIT=PITCH
AIL=AILERON
ELE=ELEVATOR
05-08-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
RC 4 life
New Heliman
Location: green bay, WI

My Posts This: Topic  Forum		swashplate issues

I'm having similiar issues with my swashplate. I've tried alot of set -ups and reading forums, watching videos, smart ass comments from my LHS and Nothing seems to help.

This is what's happening with my Blade 400; At mid throttle it doesn't want to hover (yes the battery is fully charged). AT 1/3 It wants to roll to the left. I disconnected the motor and leveled all servos and made Pitch at 60, Aileron at 60, elevator at 60, so there all equal in the Radio. Not sure what going on, maybe it's the motor? or maybe it's the ESC? It's really frustrating! (even took main shaft apart)
It was flying fine until I changed the tail rotor shaft...????
(had a hard landing on the tail)
Any help would be great!

Scott
06-15-2009 08:42 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
1 page1256 viewsPOST REPLY
Advantage Hobby . Revolution Models . CarbonXtreme

.
.
e-E-Flite Blade MSR CP CX MCX 400-3D > Blade 400 3D B400 swashplate problems after install HS65MG,need help.
 Print TOPIC Advertisers 

Subscribe to This Topic

Tuesday, November 24 - 9:26 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF