RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 627 ONLINE 80 EVENTS SEARCH REGISTER  START HERE
 
4 pages [ <<    <     2      3     ( 4 )    >    >> ]4264 viewsPOST REPLY
Futaba-RC . Boca Bearings . XHELI.COM

.
.
Aerial Photography and Video > Need help setting up a T12Zh with Hilicommand
 
 
avalon
Heliman
Location: Sydney Australia

My Posts This: Topic  Forum

Thanks. I did buy the software but my lap top did not have a coms port. I have just managed to find a USB coms port adapter and got the software to work. It all makes a bit more sense now. The gray wire can be used for controlling rate/HH as the mode changes on the screen when I flick the switch. So far so good. One thing I am not sure about if I change the travel settings under mixer nothing happens at the servo. Do I have to write this to the Helicommand before it will show the changes? With any luck I will test fly this tomorrow.

There I was inverted nothing on the clock but the makers name and only the joystick in my hand
10-04-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
rerazor
Elite Veteran
Location: Mich.

My Posts This: Topic  Forum		Yes, all changes have to 'write' in the software for it to take effect.
10-04-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
c130pilot
Senior Heliman
Location: Windsor, CO

My Posts This: Topic  Forum		Noobs,

You rock! Thanks for the crazy detailed post. I'm using a 9CHP but it was good enough for me to be able to apply it all to my radio. Thanks for the help. Not sure I could have set this crazy thing up without your post - at least not as quickly. Just test flew it a few minutes ago and it worked as advertised! Now I have to go to work on fighting some right drift, but other than that it works well.

One question for you or anyone else who wants to chime in...

I've assigned the gain control to the left slider on my 9CHP. The way I have it is that when the slider is centered, the HC is off, when the slider is down it's in position mode with increasing gain as I slide down further, and in horiz mode with increasing gain as the slider goes up... is this how others are doing it? The only downside is finding center while flying... it does beep in the middle, but I just want to see how others are setting this up.

Thanks!
Tim
.

Help! I'm umop apisdn
10-06-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
nooobs
Elite Veteran
Location: web

My Posts This: Topic  Forum		...
10-06-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
roinides
Heliman
Location: Greece

My Posts This: Topic  Forum		One extra question, even though the posts are more than detailed...

Can i use DX7 woth helicommand 3d and a ds760 gyro?
I believe i will have left only one aux2 channel for the hc.

Will it work ok, or i should go on a jrx9303?

700e
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
nooobs
Elite Veteran
Location: web

My Posts This: Topic  Forum		...
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
roinides
Heliman
Location: Greece

My Posts This: Topic  Forum		Thank you, noobs for your answer.

I read the posts above.
i will get a x9303 in the future, for now i will use the dx7!I see Avalon has the dx7, but will use the built in gyro. So he is exactly at 7 channels.

If i have a spartan gyro, it will occupate the rudder and gear channels.

So that leaves one channel for pilot or autotrim. I think , read the helicommand manual, i will not apply the autotrim plug. Just the pilot!




700e
12-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
BULLSEYE
Senior Heliman
Location: Texas

My Posts This: Topic  Forum		Noobs,

I noticed your awesome instructions are missing the pics. Do you think you can help a brother out?

Thanks buddy!!
10-12-2009 05:30 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
nooobs
Elite Veteran
Location: web

My Posts This: Topic  Forum		...
10-12-2009 06:42 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
BULLSEYE
Senior Heliman
Location: Texas

My Posts This: Topic  Forum		Thanks!
10-12-2009 06:08 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
gtxkid
Senior Heliman
Location: Pueblo Colorado

My Posts This: Topic  Forum		Well since i started this thread back in 4-12-2008 i'm back.
Never gave up.
If it wasn't for Noobs i would be dead in the water.
Well after killing a 9254 tail servo and a JR DS3421 i now have made the conection to the computer with it working.
I still have to set up pitch and such.

Under Daignose tab i notice the purple bar goes from the center to the nose right when i move my stick to the left.
Hmmmm seams backwards but looks to be correct on heli.

I am going to get it done no mater how long it takes or what it costs.
Greg

Logo 10 3D--NEU 1910 1Y motor--Castle creations 45HV and 80 AMP--Gy401 w-9254--Futaba T12ZH --JR ser
11-22-2009 07:09 PM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
4 pages [ <<    <     2      3     ( 4 )    >    >> ]4264 viewsPOST REPLY
Advantage Hobby . Revolution Models . CarbonXtreme

.
.
Aerial Photography and Video > Need help setting up a T12Zh with Hilicommand
 Print TOPIC Advertisers 

Subscribe to This Topic

Friday, March 19 - 1:02 pm - Copyright © 2000 - 2010 runryder.com | email | link to rr | START HERE | NF