RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 667 ONLINE 18 EVENTS SEARCH REGISTER  START HERE
 
4 pages [ <<    <     1     ( 2 )     3      4     NEXT    >> ]9177 viewsPOST REPLY
Heli Wholesaler . JR-Spektrum . E-flite

.
.
Blitz Helicopters Avro 90 > AVRO Hall of Fame
 
 
Jonty
Veteran
Location: NZland

My Posts This: Topic  Forum

Hey guys

I have all my electronics ready for my Avro (which I will order soon). I am going with:

611/BLS
8915 (cyclic)
9255 throttle
OS90 hyper (non pumped)
Multigov
Fromeco 8V 5200 mah
CY blades


Question, have any of you used the new MP5 or is a hatori a better fit? If so what model Hatori?

Cheers all, will post once complete
02-17-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
Real Raptors
rrAdvertiser
Location: UK

My Posts This: Topic  Forum		Hi Jonty
Both pipes fit ok, the mp5 fits with no mods, but the hatori you will need to cut the fan shroud a bit, but we do have a template for this

The hatori pipe will depend on the engine, os 939 or ys 937

Andy
02-17-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Jonty
Veteran
Location: NZland

My Posts This: Topic  Forum		Great, thanks Andy
02-18-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
delhezi18
Senior Heliman
Location: jakarta,indonesia

My Posts This: Topic  Forum		anyone knows the thickness of one body frame?
02-18-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
AreA51tje
Senior Heliman
Location: Murcia, Spain

My Posts This: Topic  Forum		Hi delhezi18,
I just measured the frame plates and the complete thikness of the chassis:

Carbon plate: 2mm or 0.079 inch
Thiness complete frame: 29.80mm or 1.17 inch

Hope this answers your question!

Regards,
Dave
02-18-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
AreA51tje
Senior Heliman
Location: Murcia, Spain

My Posts This: Topic  Forum		Hi Guys, Finally last weekend allthough the bad weather conditions a good girlfriend Raquel did the honour to fly my AVRO in some nice 3D Action...

Will send soon some more sunny pictures :)

Saludos, Dave

02-19-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
ANDYC
Heliman
Location: BICESTER/OXON england

My Posts This: Topic  Forum		At last!!! Avro ready for her maiden, I hope the weather is O.K. this weekend

02-21-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Olli-Pekka Mahrberg
Senior Heliman
Location: Finland, Joensuu

My Posts This: Topic  Forum		Those almost look better than the Aurora . Great design
(in the matter of fact I think they DO look better than the Aurora )


-op-
02-22-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
Raquel
Heliman
Location: Spain

My Posts This: Topic  Forum
02-24-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
rsalazar
Elite Veteran
Location: Florida, USA

My Posts This: Topic  Forum		Raquel!!

Very nice canopy
02-24-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
e-copter
rrAdvertiser
Location: Nice, France

My Posts This: Topic  Forum		Hi,

here is mine after rebuilt due (the dumbest crash ever happend in Rc Helicotpers )

Best regards,

Fabien



03-10-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Matutu
Heliman
Location: Torquay - United Kingdom

My Posts This: Topic  Forum		Wow "e-copter" love your canopy design, did you do that yourself?. How do you find seeing it in the air?.

Also want some more details on the dumbest crash which ever happend in Rc Helicopters

Again Nice looking model you get there

Matutu
03-10-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
e-copter
rrAdvertiser
Location: Nice, France

My Posts This: Topic  Forum		Hi,

yes we make custom canopies molds and paintings ( if you look on Blitz website on the picture slideshow, there is one same we made, but with blue candy " Blitz" logo, for Blitz Helicopters .But i can't advertise on RR . i'll put a picture of teh other one later.

Well regarding the dumbest crash, it's mroe than 10 years that i build and setup helicopters for people and never had any problems.

On the Avro, it was one of the forst batches and i was translating the manual in French, so i did read, build, unbuild and made corrections for the french manual, and well i was preparing Nuremberg toy fair and scale fuselages milling at the same time so i did the Avro build very late during nights.

Then i was totally excited and we took the Avro to go to the field with Dominique Buhn, and could not resist to give it a go..
And flew something like 2 minutes...; We landed witht he main gear and rotor head beeing retained by the torque tube conical gear (lol) and severe vibrations, and the heli once landed felt on the side like a big stone, in a cow sh..t . Yeah... ...

Well after deeeeeeeeep inspection, when i de-built and re-built the heli for the manual writing, i just forgot to put loctite on one full side of the heli and i even did not tightened the screws. As i did that very late, then stopped for one week and went back on the heli, i just did not give a final look ( shame on me ).

All i can say is that the Avro is a VERY robust heli, i only damaged the frames becasue of teh crown gear ripping in the frame, the upper bearing block was just not retained anymore as the screws escaped with the vibrations.

I was already paranoid about safety on gaz helicopters, now i twice more even hehehe..

it's now rebuilt with extra strong loctite and triple checked, and all i can say is that it's one of the best and strongest heli i've flown so far with my 3DNT. ))

BEst regards,

Fabien
03-10-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
e-copter
rrAdvertiser
Location: Nice, France

My Posts This: Topic  Forum		I forget to say, it's ok in the air so far, i can see it clearly and anyway i'm not a hard 3D flier so it's just fine for me, but we might test one with this Kawazaki Green and Orange or mandarin candy for the low part of the canopy.

PS: the bottom is not black, it's candy dark red with metal flakes

BEst regards,

Fabien
03-10-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
AreA51tje
Senior Heliman
Location: Murcia, Spain

My Posts This: Topic  Forum		Hi Fabian,
Indeed a very nice paint job! Could you place some more detailed pictures of your avro? Would love to see what is below that nice canopy

I love green and the visibility is not to match with yellow or orange but its perfectly visible

Anyway the Hard 3D movements is a programmed in the head of the pilot I even think he could fly it with blindfolled jeje.. would be a nice event on this years 3D masters....

Regards, Dave
03-10-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
e-copter
rrAdvertiser
Location: Nice, France

My Posts This: Topic  Forum		Hi Dave,

i will take pictures tomorrow or wednesday, only the tail servo is not on it as i need to change the gears (not received yet).

The configuration is the following:

- OS 91 SZ
- Hatori 3D Muffler
- 3 x 9255 Cyclic servos
- 1 x 9254 Throttle servo
- GY611 / 9256 tail servo
- CSM Revlock governor ( not installed during the engine break-in)
- Scott Gray Reactor X voltage regulator
- 3200 Mah 2S Lipo (thinking in going for 2s2P 4200 Mah)

Main blades are Zigsaw 700mm
Flybar paddles are Sab 3D paddles (carbon)
Tail blades are Sab 95mm (large chord) but will be swtiching to Radix 105 mm for 3D when Dominique Buhn flies it (we use it both, but i fly more gently than him hehehe )

I use a 72 Mhz PCm 10X transmitter and a RD2000 synthetised receiver.

There must be some pictures of when i mounted the Avro on some thread here, electronics was just fitted but not the wiring, i'll try to find the link. The Reactor X was not installed at that moment

BEst regards,

Fabien
03-11-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
MattJen
Elite Veteran
Location: UK

My Posts This: Topic  Forum		[quote]but the hatori you will need to cut the fan shroud a bit, but we do have a template for this

On my Hatori, i got a spacer from Blitz,which they design for the smaller hatori pipe, which moved it out further so it did not touch the fan shroud,

The long Hatori pipe sticks out further so there is no need for the spacer.

Matt
03-11-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
e-copter
rrAdvertiser
Location: Nice, France

My Posts This: Topic  Forum		Hi,

yes, on the Hatori 3D, it's needed to cut a bit the fan shroud.

Here is a picture of the cut :



BEst regards,

Fabien

PS: here are pics of the very first build

http://www.e-flex.fr/avro/rravro.zip
03-11-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
MattJen
Elite Veteran
Location: UK

My Posts This: Topic  Forum		Thanks Fabien for info

How are you finding the 3D version ?

Not knowing much about the 3D setup how does it compare the synergy ?

as a couple in my club are devout synergy flyers, and i was telling them about the Avro, but mine is in F3C setup, so although it is capable of 3D, it is not a dedicated 3D setup, using harder shims and rubbers etc.

Matt
03-11-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
ratititat
Heliman
Location: denver, co.

My Posts This: Topic  Forum		Mine is off the chain the cyclic is very fast with the 3D set up I have 90/90-90/90 with the 3d inserts.

03-12-2008 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
4 pages [ <<    <     1     ( 2 )     3      4     NEXT    >> ]9177 viewsPOST REPLY
Fast Lad Performance . Ace Hobby . Esprit Model

.
.
Blitz Helicopters Avro 90 > AVRO Hall of Fame
 Print TOPIC Advertisers 

Subscribe to This Topic

Saturday, November 21 - 8:28 pm - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF