RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 508 ONLINE 20 EVENTS SEARCH REGISTER  START HERE
 
2 pages [ <<    <     1     ( 2 )    >    >> ]2544 viewsPOST REPLY
Boca Bearings . XHELI.COM . Autography FlightPower

.
.
e-E-Flite Blade MSR CP CX MCX 400-3D > Futaba 9c question
 
 
tman52804
Senior Heliman
Location: Davenport, IA

My Posts This: Topic  Forum

bump.....
05-15-2006 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Cameron
Key Veteran
Location: St. Johns, Florida

My Posts This: Topic  Forum		Those are setting I posted some time ago and they work great but If you want full movement in the servos have a AIL Rate in SWASH AFR to about -84
These are the settings I have used for a while and they have worked for me. Inverted works fine too.
<=======================>
<= BLADE CP settings for 9C =>
<=======================>


//---------------------------------/
// Go to PARAMETER /
//--------------------------------/

Type>HELI (SR-3)
MODUL>PPM
ATL>ON

//---------------------------------/
// Go to SWASH AFR /
//------------------------------- /

RATE-AIL> -84%
ELE> +58%
PIT> +64%

//---------------------------------/
// Go to END POINTS /
//------------------------------- /

Change the throttle to 43/100
-To do this select throttle and then use the left stick to toggle to the left side to make it 43

//---------------------------------/
// Go to REVERSE /
//--------------------------------/

Reverse 1:AIL
Reverse 3:THR

//---------------------------------/
// Go to TH-CV/NOR /
//--------------------------------/

POINT 1> 0.0%
2> 25.0%
3> 50.0%
4> 75.0%
5> 100.0%

//---------------------------------/
// Go to PI-CV/NOR /
//--------------------------------/

POINT 1> 46.0%
2> 52.5%
3> 57.5%
4> 63.5%
5> 75.0%

//---------------------------------/
// Go to REVO./NOR /
//--------------------------------/

MIX>ON
POINT 1> -20%
2> -10%
3> 0%
4> +10%
5> +20%

//---------------------------------/
// Go to THR-CUT /
//--------------------------------/

-For this you can choose the switch that you want to use throttle cut
-I prefer the H switch becuase it is the easiest to reach when I am flying or when I need to use it

MIX>OFF
RATE> 0%
THR> 5%
SW> H
POSI> DOWN

<============================================================================================================>


-Now go to [ADVANCE(HELI)] menu by pressing Mode/Page button


//---------------------------------/
// Go to THR-CURVE /
//--------------------------------/

-Go up to >NORM(NORM) by using the up and down arrows
-Then Scroll with Dial to >IDL1(NORM)
-Use arrows and go down to MIX>INH and switch it to MIX>OFF using dial
-Change points to what follows:
MIX>OFF
POINT 1> 100%
2> 75%
3> 50%
4> 75%
5> 100%


//---------------------------------/
// Go to PIT-CURVE /
//--------------------------------/

-Go up to >NORM(NORM) by using the up and down arrows
-Then Scroll with Dial to >IDL1(NORM)
-Change points to what follows:
POINT 1> 22%
> 39.0%
> 57.5%
> 67.5%
> 78.5%

//---------------------------------/
// Go to HOV-THR /
//--------------------------------/

Turn MIX>ON
Rate> 0% (- 70%)
VR> +VrC
MODE> NORM
To get to - 70% use the VR(C) Knob on the TX

//--------------------------------/
// Go to HOV-PIT /
//--------------------------------/

Turn MIX>ON
Rate> 0% (+ 15%)
VR> +VrA
MODE> NORM
To get to +15% use the VR(A) Knob on the TX

//---------------------------------/
// Go to THR-HOLD /
//--------------------------------/

[THR-HOLD]
MIX> OFF
POSI> 0%

[RUD-OFST]
MIX> INH
OFFSET> 0%

<============================================================================================================>
-Idle Up 1 switch is Switch G which is Default
-You can adjust to your needs and likes
-******MAKE SURE THAT ALL OF THE SETTINGS ARE RIGHT BEFORE FLIGHT IS ATTEMPTED!!!!!!!!********


//---------------------------------/
// Credits /
//--------------------------------/

-If you need any help with these settings PM on Runryder
-My name is WingsWest328
-If further help is needed you can catch me on AIM: WingsWest328
-Hope these settings work for you, and have fun flyi

Cameron
05-30-2006 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE   GALLERY
 
 
Intruder
Senior Heliman
Location: Algonquin, Illinois

My Posts This: Topic  Forum		Throttle end point ?

why do you change the lower range of the throttle endpoint to 43 ?

Curious as to the reason for this change ??????????????????????????

Ken

UP = Away From The Center Of The Earth
07-14-2006 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
patternrules
Heliman
Location: Nineveh, IN

My Posts This: Topic  Forum		Ok I'm new at heli's so I copied the program above and it seems to work fine with one small difference from the stock setup, the tail rotor doesn't start till after the main blades and has a hard kick when it does start, with the stock TX the tail rotor always started first with no hard kick just smooth and was very solid thoughout the flight (hover), how would this be adjusted???
Thanks
P.S. on a Blade cp Pro
Steve Maxwell
10-31-2006 Over year old.
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
2 pages [ <<    <     1     ( 2 )    >    >> ]2544 viewsPOST REPLY
Advantage Hobby . Revolution Models . CarbonXtreme

.
.
e-E-Flite Blade MSR CP CX MCX 400-3D > Futaba 9c question
 Print TOPIC Advertisers 

Subscribe to This Topic

Sunday, November 8 - 5:40 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF