RR Rated M For Mature
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 406 ONLINE 20 EVENTS SEARCH REGISTER  START HERE
 
2 pages [ <<    <     1     ( 2 )    >    >> ]1676 viewsTOPIC CLOSED
Power Helis . CANOMOD . Experience RC

.
.
e-MS Composit Hornet > Hornet II Main Blades hitting tail rotor blades
 
 
Micro-Maniac
Elite Veteran
Location: Pasco,Washington Formerly: Captain Chaos

My Posts This: Topic  Forum

Um, madcratebuilder..

From where to where did you measure the H2 boom? I think your 11in is from where it exits the frame instead of it's full length from gear to gear.
02-22-2006 02:20 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
duenaz
Heliman
Location: Colorado Springs, Colorado USA

My Posts This: Topic  Forum		i've got 258-260mm blades. I ordered the right tailboom and driveshaft. Thanks guys
02-22-2006 02:21 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
pcdonovan
Heliman
Location: Miller Place, NY

My Posts This: Topic  Forum		X3d and HII use the same e416 boom

I'm not madcratebuilder but.. I have the answer... do I get a prize
haha

also if I'm not mistaken the OD on the tailboom is closer to 7.5mm

Hornet II
02-22-2006 02:21 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
duenaz
Heliman
Location: Colorado Springs, Colorado USA

My Posts This: Topic  Forum		tailboom for H2 is 7.6mm pretty close there pcdonovan.. ever since I found out I had the wrong stuff i've been researching like crazy.
02-22-2006 02:36 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
pcdonovan
Heliman
Location: Miller Place, NY

My Posts This: Topic  Forum		http://www.mscomposit-usa.com/shopo...ocs/manuals.php

Here are the manuals in pdf. for all of the hornet range you have seperate instructions and drawings for each. Great site to book mark. I have already started to install X3d parts on my H II if any of you guys have the plastic hiller, and have had the little posts break away from the hiller main section, use the X3d part the hiller mixer arms attach via bolts no more plastic crap post and ca'ing that little rubber grommet. Its a direct replacement.

Hornet II
02-22-2006 02:40 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE  
 
 
Blade-X
Senior Heliman
Location: Singapore

My Posts This: Topic  Forum		:Heard that.... I did try to go back to my LHS to try to exchange the old one with the plastic posts for the new x3d bell-hiller head.. but to no avail...
02-22-2006 05:03 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   GALLERY
 
 
madcratebuilder
Heliman
Location: Northern Orygun USA

My Posts This: Topic  Forum		Captain Chaos, you are correct I measered frame to rear gear.


pcdonovan, my H2 boom is 7.57 when I bother to get the dial calipers out. I was eyeballing it.
The point is the h2 boom is about 1in longer and 1mm larger in diameter.
Obviously larger than the Hornet fp, cp or cpx.
02-22-2006 05:37 AM
PROFILE   PM   EMAIL   POSTS   BUDDY   IGNORE   HOMEPAGE  
 
 
2 pages [ <<    <     1     ( 2 )    >    >> ]1676 viewsTOPIC CLOSED
Heli-Max . Hobby Hut . Heli Wholesaler

.
.
e-MS Composit Hornet > Hornet II Main Blades hitting tail rotor blades
 Print TOPIC Advertisers 

Subscribe to This Topic

Sunday, November 8 - 7:29 am - Copyright © 2000 - 2009 runryder.com | email | link to rr | START HERE | NF